Tualatin Posted July 28, 2013 Share Posted July 28, 2013 Hi folks! I have a strange problem. After I update my DCS-World from 1.2.4 to 1.2.5 I can't start BS2 because the software says there a no valid Serial Number. I can not deactivate the software, than I get a error: No license for deactivation is found. To obtain an error report and send it to product technical support, press the corresponding button. What is the problem? :( [sIGPIC]http://forums.eagle.ru/signaturepics/sigpic34649_6.gif[/sIGPIC] VKB Gunfighter MCG Pro Mk.II, VKB T-Rudder Pedals Mk.IV Link to comment Share on other sites More sharing options...
Panzertard Posted July 28, 2013 Share Posted July 28, 2013 1. Use this procedure to clear the Serial from registry. Sticky: Activation failed with "invalid hardware code"? 2. If it says it's a invalid serial after that use this procedure, start BS2 again and it should be okai: We have created a page to manage serial numbers. It's very basic now. Right now it's possible only "to release" serial numbers. http://www.digitalcombatsimulator.com/myserials.php When you might need it. There is an error during login. Eg. "Invalid Product Key". It might appear when serial number is bound to one website account and you login with another one. Then you open this page and unbind your serial number. You don't need to find the right account any more. Just unbind serial number and login with any account. The mind is like a parachute. It only works when it's open | The important thing is not to stop questioning Link to comment Share on other sites More sharing options...
Tualatin Posted July 28, 2013 Author Share Posted July 28, 2013 It does not work for me. All modules (A-10, P51D, UH-1H) works well but Blackshark 2. When I try to enty my Serial number I get the following message now: "The system requires the correct Serial Number of the application to perform this operation. The Serial Number entered is wrong or mistyped. Enter a valid Serial Number and try again." Whats wrong?? [sIGPIC]http://forums.eagle.ru/signaturepics/sigpic34649_6.gif[/sIGPIC] VKB Gunfighter MCG Pro Mk.II, VKB T-Rudder Pedals Mk.IV Link to comment Share on other sites More sharing options...
Nate--IRL-- Posted July 28, 2013 Share Posted July 28, 2013 (edited) Sounds like the wrong version of BS2 is installed - please check you have the correct one (Upgrade or Full) that matches your Key type. Not sure why this would have happened though. Nate Edited July 28, 2013 by Nate--IRL-- Ka-50 AutoPilot/stabilisation system description and operation by IvanK- Essential Reading Link to comment Share on other sites More sharing options...
Tualatin Posted July 28, 2013 Author Share Posted July 28, 2013 I had downloaded the upgrade version, because I have a upgrade serial key. I'm absolutely sure that is the right version. Hmm [sIGPIC]http://forums.eagle.ru/signaturepics/sigpic34649_6.gif[/sIGPIC] VKB Gunfighter MCG Pro Mk.II, VKB T-Rudder Pedals Mk.IV Link to comment Share on other sites More sharing options...
Keats Posted July 28, 2013 Share Posted July 28, 2013 Try selecting 'DCS BS2 upgrade from BS1' instead of 'DCS BS2 international key' in the installer. Link to comment Share on other sites More sharing options...
Tualatin Posted July 29, 2013 Author Share Posted July 29, 2013 Try selecting 'DCS BS2 upgrade from BS1' instead of 'DCS BS2 international key' in the installer. That was my miss! Thank you! Now it works again. [sIGPIC]http://forums.eagle.ru/signaturepics/sigpic34649_6.gif[/sIGPIC] VKB Gunfighter MCG Pro Mk.II, VKB T-Rudder Pedals Mk.IV Link to comment Share on other sites More sharing options...
Recommended Posts