OutLord Posted September 27, 2018 Share Posted September 27, 2018 So, I follow procedure for BIT test and sometimes it works and sometimes it doesnt. the DDi says In Test but the surfaces are not moving. I read you have to disengage NWS but doesnt seem to help Reset FCS and Trim, Flaps to Auto. Not sure what other tricks I could be missing. Link to comment Share on other sites More sharing options...
Svsmokey Posted September 27, 2018 Share Posted September 27, 2018 Are you using two inputs simultaneously ? One is as i recall and osb press , and you have to be holding a pushbutton on the right side cockpit simultaneously if memory serves... 9700k @ stock , Aorus Pro Z390 wifi , 32gb 3200 mhz CL16 , 1tb EVO 970 , MSI RX 6800XT Gaming X TRIO , Seasonic Prime 850w Gold , Coolermaster H500m , Noctua NH-D15S , CH Pro throttle and T50CM2/WarBrD base on Foxxmounts , CH pedals , Reverb G2v2 Link to comment Share on other sites More sharing options...
OutLord Posted September 27, 2018 Author Share Posted September 27, 2018 Are you using two inputs simultaneously ? One is as i recall and osb press , and you have to be holding a pushbutton on the right side cockpit simultaneously if memory serves... yes hold up the BIT test switch and press the left top DDI pb. Link to comment Share on other sites More sharing options...
Svsmokey Posted September 27, 2018 Share Posted September 27, 2018 Forgive the question but...engines running ? 9700k @ stock , Aorus Pro Z390 wifi , 32gb 3200 mhz CL16 , 1tb EVO 970 , MSI RX 6800XT Gaming X TRIO , Seasonic Prime 850w Gold , Coolermaster H500m , Noctua NH-D15S , CH Pro throttle and T50CM2/WarBrD base on Foxxmounts , CH pedals , Reverb G2v2 Link to comment Share on other sites More sharing options...
OutLord Posted September 27, 2018 Author Share Posted September 27, 2018 thats's ok, yes and set to idle. I can ignore the test and take off fine. Link to comment Share on other sites More sharing options...
OutLord Posted September 27, 2018 Author Share Posted September 27, 2018 my checklist 1 BATTERIES 2 WARNINGS TEST 3 APU ON 4 ENG CRANK RIGHT 5 RIGHT ENG IDLE 6 OPEN BLEED AIR VALVES 7 DDI'S TO DAY POSITION 8 LEFT DDI FCS 9 RESET CAUTIONS 10 INS TO GROUND 11 ENG CRANK LEFT 12 ENGINE LEFT IDLE 13 FCS RESET 14 OBOGS ON (OXYGEN) 15 RADAR ON (GROUND / SILENT) 16 FLAPS TO AUTO 17 RUN A BIT FAILURES TEST 18 FLAPS TO HALF FOR TAKEOFF 19 RESET TRIM BUTTON 20 UNCAGE BACKUP ADI 21 CLOSE CANOPY 22 INS TO NAV 23 LEFT DDI HUD 24 RIGHT DDI FCS 25 HANDBRAKE Link to comment Share on other sites More sharing options...
Svsmokey Posted September 27, 2018 Share Posted September 27, 2018 Sounds like we've covered everything . Perhaps a bug report is in order . And nice checklist ! 9700k @ stock , Aorus Pro Z390 wifi , 32gb 3200 mhz CL16 , 1tb EVO 970 , MSI RX 6800XT Gaming X TRIO , Seasonic Prime 850w Gold , Coolermaster H500m , Noctua NH-D15S , CH Pro throttle and T50CM2/WarBrD base on Foxxmounts , CH pedals , Reverb G2v2 Link to comment Share on other sites More sharing options...
bradleyjs Posted September 27, 2018 Share Posted September 27, 2018 Before you click the OSB press and hold the “Y” key simultaneously. Alienware Area 51 R5 - Intel i9 7980XE (4.7 GHz), 32GB Dual Channel HyperX DDR4 XMP, Dual NVIDIA GeForce GTX 1080 Ti Graphics 11GB GDDR5X SLI, 4.5 TB combo of SSDs/HDDs, Alienware 1500 Watt Multi-GPU Power Supply, Alienware 25” 240Hz Gaming Monitor, Alienware Pro Gaming Keyboard, TM HOTAS, TM Cougar F-16C MFDs, Saitek Pro Flight Rudder Pedals, TrackIR5, Win10 Pro x64 Link to comment Share on other sites More sharing options...
Recommended Posts