Jump to content

Search the Community

Showing results for tags 'warthog'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • News
    • Official Updates
    • Community News
  • DCS World Tutorial & Training Range
    • New User Briefing Room
    • Guides & Tutorials
  • English
    • Digital Combat Simulator
    • DCS World War II
    • DCS World Topics
    • Licensed Third Party Projects
    • Reality
    • Legacy Versions
  • International support
  • Русский
  • DCS Finland's DCS Finland
  • 3Sqn's 3Sqn
  • 49th Black Diamonds's 49th Black Diamonds
  • -=Пилотажники=-'s -=Пилотажники=-
  • Polacy's Polacy
  • = Flammeus Vulpes = fighting squadron's = Flammeus Vulpes = fighting squadron
  • Banda-DV's Banda-DV
  • Comedy Central's Comedy Central
  • =UVAF='s =UVAF=
  • 100 KIAP's 100 KIAP
  • VVS 504th Red Hammers's VVS 504th Red Hammers
  • Lock-On Mod Makers's Lock-On Mod Makers
  • Sweden's Sweden
  • Leftside Limited Tech section's Leftside Limited Tech section
  • Ground Troops Aviation Training Center's Ground Troops Aviation Training Center
  • German DCS Community's German DCS Community
  • Spanish DCS Community's Spanish DCS Community
  • °United Fight Spirits° - Germany's °United Fight Spirits° - Germany
  • Чат's Чат
  • RedRodgers's RedRodgers
  • Совместные вылеты онлайн's Совместные вылеты онлайн
  • -=Air piretS=-'s -=Air piretS=-
  • Клуб Веселых Пилотов/Smile Pilots Club's Клуб Веселых Пилотов/Smile Pilots Club
  • 161 Squadron's 161 (Recce) Squadron
  • German DCS Serveradmins's German DCS Serveradmins
  • Escuadrón 701, Colombia's Escuadrón 701, Colombia
  • LowLand Tiger Meet's LowLand Tiger Meet
  • 279KIAP Regiment's 279KIAP Regiment
  • Australian DCS Community's Australian DCS Community
  • Scandinavia's Scandinavia
  • Crazy Canuks's Crazy Canuks
  • The Silver Falcons's The Silver Falcons
  • 127Th Sibйrian Tiger's 127Th Sibйrian Tiger
  • 129th A-10 Squad: The Guard Sharks's 129th A-10 Squad: The Guard Sharks
  • Virtual Red Arrows's Virtual Red Arrows
  • Hellenic Pilots's Hellenic Pilots
  • =2IAE='s =2IAE=
  • 16th ACCW Tigers DEN's 16th ACCW Tigers DEN
  • USMC Veterans's USMC Veterans
  • United States Air Force's United States Air Force
  • =BAF='s =BAF=
  • Fighter Combat Simulations's Fighter Combat Simulations
  • =Воздушные Войны= aka =BB='s =Воздушные Войны= aka =BB=
  • CADelta's CADelta
  • DCS: Combined Arms's DCS: Combined Arms
  • Oceanic Wing and Friends's Oceanic Wing and Friends
  • The Virtual Horsemen's The Virtual Horsemen
  • Hellas's Hellas
  • NoPryl Warthog Squadron's NoPryl Warthog Squadron
  • Aeronautica Militare Virtuale Italiana's Aeronautica Militare Virtuale Italiana
  • Carrier Air Wing Seventeen — CVW-17 —'s Carrier Air Wing Seventeen — CVW-17 —
  • 蜂鸟特技飞行表演队 HummingBird Aerobatics Team's 蜂鸟特技飞行表演队 HummingBird Aerobatics Team
  • 1st Cav Div (Air Assault)'s 1st Cav Div (Air Assault)
  • CrimsonFlag - 102° GVv's CrimsonFlag - 102° GVv
  • AIEclan's AIEclan
  • Virtual Black Sheep's Virtual Black Sheep
  • 929th's 929th
  • French DCS Community's French DCS Community
  • 373rd Online Tactical Campaigns's 373rd Online Tactical Campaigns
  • Just For Laughs Simulation DCS's Just For Laughs Simulation DCS
  • "Russian Air Force" =RAF='s "Russian Air Force" =RAF=
  • ECV56 Cóndor's ECV56 Cóndor
  • Master Arms's Master Arms
  • 141 Wolfs's 141 Wolfs
  • 314. ШАП Моздок (Су-25)'s 314. ШАП Моздок (Су-25)
  • Escuadrón 117's Escuadrón 117
  • Austian/Germany Pilots's Austian/Germany Pilots
  • Итория авиации's Итория авиации
  • Clan Vikingos's Clan Vikingos
  • Virtual Royal Danish Airforce's Virtual Royal Danish Airforce
  • United Operations Air Forces's United Operations Air Forces
  • United States Navy's United States Navy
  • Europe clan's Europe clan
  • No.66 Squadron's No.66 Squadron
  • De Belgae's De Belgae
  • v47th Fighter Squadron's v47th Fighter Squadron
  • 105 Wirtualny Pułk Śmigłowców Bojowych (105th Virtual Combat Helicopters Regiment).'s 105 Wirtualny Pułk Śmigłowców Bojowych (105th Virtual Combat Helicopters Regiment).
  • 7 Wirtualna Eskadra Działań Specjalnych's 7 Wirtualna Eskadra Działań Specjalnych
  • 223rd CAS "Wolfpack"'s 223rd CAS "Wolfpack"
  • www.TAW.net - DCS Division's www.TAW.net - DCS Division
  • Jagdfliegergeschwader 1 “Fritz Schmenkel” (JG-1)'s Recruitment
  • 64th Aggressor Squadron - Public's Images and Videos
  • =BK= Братские крылья's Связь
  • =BK= Братские крылья's Сервера =BK=
  • =BK= Братские крылья's Вопросы
  • Virtual Carrier Air Wing 1's Topics - Bugs
  • Virtual Carrier Air Wing 1's COOP Flights - Request
  • Virtual Carrier Air Wing 1's Video and Live Feed
  • Virtual Carrier Air Wing 1's Recruitment questions
  • Air Combat Wings's Video
  • DTA - Comunidad Hispana de DCS's Muro
  • Virtual Skyblazers's Information
  • Virtual Skyblazers's Conversation
  • The Flying Kiwis's The Flying Kiwis Zorb ball of death dedicated server
  • The Flying Kiwis's ANZAC Mission
  • LINCI's Discussioni
  • [OFS] Open Flight School's Informationen
  • The Pirates Cove's Mods
  • The Pirates Cove's C-130 MOD
  • VF-211's Contact us
  • Comunidad Española de DCS - Interescuadrones's Discusiones
  • Sabre Squadron's Campaign & Mission Updates
  • Neko PMC's Topics
  • 74th Flying Tigers's Questions and Answers
  • Red Air College's About RAC
  • Cerberus Fighter Wing's Screenshot Posting
  • Digital Coalition Air Force's Posts/Forum
  • Strike Fighter Squadron's VMFA-35 Skin by Stellou
  • 1st VFW's General Discussion
  • VFA-41 Black Aces's VFA-41 Black Aces Squadron Info
  • 154th Air Wing's New Server
  • Task Force Uniform Charlie Sierra's Links
  • delete's The discord link
  • 1(F) Squadron RAF Air UK's Operations
  • TFB 8's Dedicated Public Servers
  • 枝江虚拟航空队's 涂装展览


  • Community Calendar
  • Jagdfliegergeschwader 1 “Fritz Schmenkel” (JG-1)'s Events
  • ASOR 234 squadron's Operations
  • 11TSG's Events
  • 51st Virtual Fighter Wing's Events
  • DCS-HAF's PvP Events
  • DCS Español || D3W's Calendario
  • DTA - Comunidad Hispana de DCS's Eventos
  • DCS - Allied Forces - Open Missions and Beyond's Events
  • The Flying Kiwis's TFK Flying schedule
  • VF-211's Training nights
  • VF-211's Calendar
  • Comunidad Española de DCS - Interescuadrones's Eventos
  • Neko PMC's Events
  • VFA-86 Sidewinders's Winder schedule
  • 74th Flying Tigers's Trainings and Missions
  • Cerberus Fighter Wing's Events
  • Digital Coalition Air Force's Events
  • uosef's عقابهای ایران
  • v81st Fighter Squadron's Training and Operations
  • Darkwater Aerial Security Ltd. (Task Force "Caucasus Dragons")'s Contracts and Operations
  • Darkwater Aerial Security Ltd. (Task Force "Caucasus Dragons")'s Events
  • Delta Force Squadron's Events
  • Virtual Fighter Group's Schedule

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start



Flight Simulators





Found 17 results

  1. UPDATE: Version 2.62 is available. The installer will now give you the option to install CTS for DCS 2.5 and 1.5.8 Legacy versions. Note: The DNS address in the old 2.10 installer is no longer valid. Copy the version.txt attached to this post into your CTS\DB folder before running the updater. Alternatively, the 2.55 installer is available in the links below. Special thanks to Tercio Sampaio for developing the GUI. If you wish to donate for this program, please send any donations to Fisher House, a charity that supports wounded veterans and their families. Exception: if you want me to program for a module or hardware I don't have, please PM me and we can discuss it. DCS World TARGET Script for Thrustmaster Cougar or Warthog and MFDs is now available. Download it from: Eagle Dynamics User Files Box.com This file is an installer which will install and launch the updater, which will then download the latest version of the script. You can also periodically run the updater to keep your script up to date. This script for the HOTAS Cougar/Warthog and Cougar MFDs includes dedicated profiles for the following aircraft: A-10C Warthog AV-8B N/A Harrier II Ka-50 Black Shark P-47D Thunderbolt P-51D Mustang UH-1H Huey Mi-8 Hip Mi-24P Hind F-86 Sabre Fw-190A8/D9 Bf-109K-4 Kurfürst MiG-21bis Fishbed MiG-15bis M-2000C SA-342 Gazelle L-39 Albatross F-5E Tiger II Spitfire LF Mk. IX Mosquito FB Mk. VI AJS-37 Viggen C-101 F-14 Tomcat F-16C Viper JF-17 Thunder F/A-18C Hornet MiG-19 Farmer I-16 Ishak A-4E Skyhawk MB339 T-45 Goshawk Combined Arms Flaming Cliffs 3 The script is fully implemented with both code and custom keyboard and joystick LUA files. The included "Standard DirectX" profile can me used to create a versatile profile for anything else. This script uses TARGET, so you need to install it (though Cougar users can leave Foxy where it is). I also recommend the latest MFD Drivers, as I have found fewer profile crashes with these enabled. The script offers the following features: Graphical User Interface (GUI) to save your settings and auto-generate script files. Both HOTAS Cougar and Warthog Compatibility with New F/A-18 Grip Support for selected modules. All documentation (except for the Setup Guide) is in HTML with context-sensitive help in the GUI. CommState routine allows for the selection of F1 through F12 keys with Hats 2-4 while the MIC switch is pressed Hot-selectable “TriggerZoom” allows you to zoom into your target or HUD when depressing the first trigger stage LED indications for airbrake, landing gear, TriggerZoom, CommState, and Teamspeak3 PTT Compatible with TouchControl (formerly TouchIR), VAICOM Pro, DCS Simpleradio Standalone, and all major VoIP solutions Optimized for TrackIR, but compatible VR or with Hat1 as POV Individual HOTAS profiles are mapped as closely to their real world counterparts as practical Flaming Cliffs 3 (FC3) HOTAS mappings correlate to the A-10C (attack aircraft) or F-16C (fighters) as closely as practical FC3 Context Sensitive Autopilot routine that reverts to last used mode on toggle A-10C Profile includes direct entry for CDU, CMSP, and UFC Ka-50 Profile allows direct entry for ABRIS (RMFD) and Rubicon Datapad Ability to automatically pause TrackIR while at the Door Gunner Station (UH-1) Context sensitive communications menus based on crew station (framework in place for DCS implementation) TARGET based Central Position Trimmer Mode that greatly improves upon the default trimmers when not using force feedback. Analog and digital differential braking routines, including paddle braking and nosewheel steering. Kneeboard mapping for all aircraft. NVGs for all capable aircraft, including "bonus" mapping for the A-10A, Su-25, Su-25T, and F-86 (H/T Zaelu). AWACS Mode for LotATC and SRS users. Simplified hot-selection of aircraft allows for potentially thousands of aircraft and variants in this script, along with audible feedback of aircraft selected. Screenshots are in the following post. I look forward to your feedback; any information that will help me improve this profile is greatly appreciated. To this end, there is now a public bugtracker for CTS. See the HTML documentation for instructions on how to submit a bug report or feature request. version.txt
  2. Hi all very new here, trying to follow the A10II C training flight for HOTAS, I get put in auto pilot mode and the trainer talks me through the different buttons, hats etc then all a sudden, the auto pilot disengages and i spiral ground words and I crash. My question is this Is there a recommended Warthog combo profile that I can download from somewhere I also have TM MFD and Crosswinds MFG pedals in my setup. Many thanks for any help? Kind regards Humpster
  3. My Thrustmaster warthog joystick died. I was installing an extension on the stick and as I did so it made a couple of chirps and then the joystick column on the DCS controls disappeared. Now when I plug the joystick into that or anyother computer it is DEAD. No chirp and not recognized. I plugged it into my other computer which is running DCS with a a TMWH and it is dead there too. Has the firmware in the base been damaged? Can I reset/reflash the firmware? Can I send it to Thrustmaster for repair? Any help will be much appreciated.
  4. A few days ago my Warthog throttle died like so many others and I just wanted to post a quick fix that just might get you going again until you can sort it out with an official board replacement/repair. This worked for me and I have not seen anybody else recover their throttle in any posts I have read. I found that by reducing the 5V line on the USB cable to less than 4.5V, the throttle came back to life. I did this by simply putting a Non powered USB hub between the throttle and PC, you could also add some other items onto the hub to load it down a bit more. Most people seem to try connecting direct to system board or another powered USB hub thinking it might be a low voltage issue causing the throttle to fail, which is the logical way to think. Another alternative would be to supply your own external power to the USB line to the throttle only that can be adjusted to less than 4.5V, isolating the power line from the PC/Hub, but only do this if you are confident in what you are doing. If you are faced with a dead throttle or stick give it a try, if you have had a failed firmware update you will have to do the firmware update again and get the last green verification tick before it will work properly. You can read my full ordeal with this issue here: https://forums.eagle.ru/forum/english/dcs-world-topics/input-and-output/thrustmaster-aa/64402-post-motherboard-specs-of-bricked-tm-warthogs-here-please?p=7130525#post7130525 Cheers Tri.
  5. Thrustmaster mods --------------------------------------------- F/A-18C (Hornet) grip upgrades OTTO P1 push buttons | OTTO T4 trim switch | OTTO T5 sensor control switch F-16C (Cougar) grip upgrades OTTO P1 push buttons A-10C (Warthog) grip OTTO P1 push buttons | OTTO T4 trim switch | OTTO T4/T5 hat switches for TMS/DMS/CMS A-10C (Warthog) throttle NEW--> Full mil-spec switch upgrade [OTTO, Cutler-Hammer, Honeywell, Mason] --------------------------------------------- Just a heads up, guys - the friendly engineers at Thrustmaster made it easy to swap their stock TM buttons with OTTO buttons to massively improve the clickity on the new Hornet grip same as what you can do on the Warthog grip. I opted for the 2.5 lbs actuation force for the pinkie and full 4 lbs for the pickle button. OTTO product numbers are P1-11111 and P1-11121 respectively: Here we go mashing buttons on the grip like a fool. No trouble reaching anything. Disassembly of the grip is pretty straightforward but you will run the risk of bricking it and you will probably void your warranty. First remove the paddle lever by unclipping the c clip and pushing the shaft pin out. There’s a spring in there and a small washer on the shaft. Unscrew the three hex bolts in the handle and pop the cover off. One of my bolts wanted to stay in the grip. Unscrew the PCB and push it out of the way. Unscrew the neck part that’s held in by a single bolt that also holds the ground wire and a small lock ring. Disconnect the pinkie button connector from the PCB and pop the button out through the front by pushing in the tabs on either side. You may need to rotate the button in place with pliers to be able to access both tabs. Cut the wires, strip the ends and solder them onto the OTTO button. You’ll want as much wire as possible for the new button as it can get a little tight in there. The OTTO button has a smaller diameter than the TM button so wrap some electrician’s tape around it; press it into the grip and connect it to the PCB. Fasten the neck part and PCB back into the grip and move on to the top part. Unscrew the two outer screws in the top part and pop the plastic top back and rotate it out of the way. The pickle button should be easy to pop out by pressing the two tabs in. Note that you have to cut the wires before removing this button, unless you want to try to disconnect it at the main PCB and re-threading the wire back down the neck of the grip. Replace it with the OTTO button same way as the pinkie button: leave as much wire in place in the grip as possible and use electrician’s tape to make a tight fit. You could file down the contacts or remove some plastic backing in the grip at this point if you want to set the OTTO button as deep as the stock button. I didn’t do it so mine sits at a very slight angle. Be careful not to pinch the flimsy wires and screw the top part and cover back on the grip. The paddle lever goes on last and it can be a bit tricky to get the spring seated correctly. Upgrade complete! Here's a short video showing how to get the paddle lever spring back on: In terms of difficulty I’d say this is easier than modding the Warthog since there’s fewer buttons to mess with. I suppose you could change the spring or the tact switch on the Hornet paddle lever but it’s not going to be as much of an upgrade as what’s possible on the warthog with a P1-11122. Compared to the Cougar though this is a walk in the park. Seriously. Don’t mess with the Cougar like I did. It takes a lot of Dremel grinding to fit the OTTOs in there and the result is not going to be as neat as what’s easily possible on the Warthog. Also, the new pinkie switch gets in the way of the paddle switch since they’re much closer together. Well, good luck if you decide to mess with your grips!
  6. Hi, i switched from the warthog throttle to the CM3 a couple of weeks ago and like it very much. My only downside is that I am missing the feel of the different buttons e.g. the China hat and boat Switch on the warthog. It’s not so easy to differentiate the buttons on the CM3. is there a way to change them or has anyone made custom buttons?
  7. --------------------------------------------- Warthog throttle NEW-> Upgrading the throttle panels Warthog, Hornet and Cougar stick grips Mil-spec upgrades for Thrustmaster stick grips --------------------------------------------- I've upgraded all switches to mil-spec on the Warthog throttle to improve the switch feel and make it more functionally realistic. This is probably only of interest if you really like the A-10C. This includes mil-spec locking and standard Eaton/Cutler-Hammer switches on the panel, the locking flap switch, OTTO push buttons and a functioning Honeywell mag switch. I had to provide 12VDC and install an Arduino running DCS-BIOS and a MOSFET circuit to control and sync the mag switch with DCS. Due to the size of the mag switch I had to extend the height of the throttle body with a simple 3D printed frame. On the throttle grips I put in all Eaton/Cutler-Hammer and one Honeywell toggle switch, OTTO hat switches and push button, and a Mason force transducer slew control out of a real F15 throttle unit. The force transducer is interfaced directly with the throttle using a small prototype PCB from Deltasim. I couldn't fit the whole mechanism from the F15 so I dropped the push functionality. It does exist in the real A-10C AFAIK but it is unused so not a great loss. While I was at it, I rewired the panel backlight to the Arduino I needed for the mag switch. This allows the LEDS to be directly synchronized with the in-game panel light intensity using DCS-BIOS. We included the actual brightness parameter in the latest DCS BIOS module for the A-10C. We have it for the Hornet as well in the DCSflightpanels branch. Here's a short video showcasing the look and feel of the switches. I've listed the switches I used, what they are in the real jet (based on Deadman's list) and some Honeywell alternatives at the end that are readily available from e.g. mouser.com This mod is neither cheap nor easy to do. It could be argued that it is in fact totally unnecessary and I would for sure have loved to convert a real throttle unit instead and it probably would have been cheaper. Good luck finding one though I intend to post a more in-depth guide to the various mods later - here's the short version for now: Rip out all switches and sub PCBs Poke it a bit with a Dremel tool Install new switches and wire them up You're golden
  8. Servus, Mein Warthog Throttle von TM funktioniert plötzlich nicht mehr. Also keine Reaktion beim einstecken seitens PC oder throttle. - alle USB Ports ausprobiert - am Kabel rumgewackelt - Aufgeschraubt (innen sieht alles gut aus - soweit ich das beurteilen kann) Hat jemand schonmal sowas gehabt? Evtl ein Wackelkontakt? Hat jemand Erfahrung mit dem Support von TM? grüße
  9. Warthog and Harrier boot with Gazelle Dust Protection and IR countermeasure
  10. Hi, I installed DCS again after some months off and wanted to fly the newly purchased A-10C II. Sadly the coolie hat isn´t working. I thought maybe it is broken, but when testing and recalibrating the throttle outside of DCS everything is OK, at least in the Windows 10 testing window. Did everyone know this error or could point me to an approach how I could find out the problem? I also loaded up Arma 3, mapped the coolie hat to the vision and could without any problems move my vision in any direction using the coolie hat, so it must be a problem with DCS... I hope somebody could help me. Greetings
  11. Hi All, This is my first post on this forum. I've been playing this marvellous game for a long time. About a month ago, began to play A-10C II Tank Killer. Read lots of user guide stuff and watched so many training videos on YouTube. After a while noticed a bug or buggy thing on A10C II. Emergency Wheel Brake works decent when I use only mouse button but it doesn't work if I use keyboard buttons. All my record is on the video which is at bottom.
  12. Hi everybody, I would like to share another little project I developed in last 6 months during my spare time: a 3D printable Luftwaffe KG13B stick. As you can see project is for Warthog base but can be adapted. This is a replica of the stick used in most WWII Luftwaffe fighters such Me109 and Fw190. Starting from a free model I found on the web I deeply revised all the details in order to optimize 3D printing purpose: - Most of the screws are internal; - Models are separated in order to avoid to color them; - Internal space is adapted to common micro switch sizes; - Components thickness is enough to give strength (please note I printed it using ABS, but I think also a strong PLA can be suitable); - Fully working safety using a small magnets; - Some revisions from the original one to optimize usage. As you see replica it come out is pretty similar to real one; all parts are connected with screws and can be disassembled if needed. Screws visible are even few than the real stick, they are mainly inside the internal structure. Only lateral button needs some glue where it joins with handle, this will keep all the object completely dismountable for maintenance purposes. If anyone is interested to STL please write me a message, I decided to share them for a small price privately before start a subscription on any sharing platform (People interested might be few). I will also share schema for the internal board for the Warthog witch is by public use and far known. To resume, I include: STLs to print for yourself Renders showing how to assemble List of parts for the build (screws, resistors, etc) Schema for the internal board (working for Warthog stick) You can print for your own or, if you prefer, ask to print pieces to a 3D printing service. Obviously I will ask to use STLs for your own and keep them private.
  13. PART 1 Hello and welcome to my Thrustmaster Warthog throttle pinky switch replacement guide. I live in the UK and have found it difficult to find any information with regards to replacing the pinky switch in the UK specifically. I found numerous vids and advice on HOW to replace it, but not WHERE I could source the correct switch from in the UK. This guide presumes you are comfortable taking apart your beloved throttle and have access to, and can use, a soldering iron. No special tools are required. If you're reading this you probably already know that there are an abundance of SPDT switches out there, and if you don't know what one of those is, like I didn't, just google it. It'll make more sense. I found it difficult to decipher all the sizes and switch types so I wanted to share exactly WHAT switch I used and WHERE it came from at a very reasonable price. So lets get to it.... THE SWITCH From a reputable electronics company, RS Components. RS stock number: 7347139 REMOVAL OF SWITCH To remove, undo the 2 phillips screws holding the left throttle together. They are located on the INBOARD side of the throttle. The OUTBOARD panel that the switch sits in should now start to come away from the body of the throttle. ***NOTE - IF THE INBOARD PLASTIC PANELSTARTS TO COME AWAY, TRY TO PREVENT THIS FROM HAPPENING. THAT PART ISN'T DESIGNED TO COME AWAY WITHOUT FURTHER DISSASSEMBLY. You will find 2 black spacers inside that will become loose once the screws are fully removed. Take those out and keep them safe with the screws. At this point don't worry about which way around they go as I'll specify that later on. I'm going to have to break this post up into stages as my images are too big and limited to a max of 5MB per post.
  14. Living in Australia being so far away can suck at times, in this case Thrustmaster DO NOT have a support channel in this country. I have a Warthog Joystick that needs parts, I have examined the unit and know what I need to buy, can anyone put me in touch with a repair agent anywhere (most likely Europe or the USA, but if there's one in Asia) that would be awesome. After spending more than a $1000 on products you would think the support arm is able to support their products anywhere needed? Premium products demand a better level of support when spending this amount of money......... All I want is someone who can supply and ship parts to Australia. Thanks in advance to anyone who can help.
  15. Looking for a squadron with weekly campaign missions, realistic IADs, a great community to hang out in, and place to learn your aircraft? https://tvalhalla.com Join Us on Discord! Task Force Valhalla was founded as a place for DCS members to fly together in realistic, coordinated operations while minimizing the milsim nature of most DCS squadrons. While we do have ranks, they are solely tied to the proven proficiency in your airframe, and our squadron commanders are chosen by community vote for their dedication in their airframe. We try to democratize as much as possible in the Task Force and have representatives from all squadrons provide input and vote on any changes that affect everyone. We'd like to think our missions are unique, and we hope to get more active mission makers to increase the storytelling and depth available to our members. We currently use HighDigitSAMs integrated with Skynet-IADS in all of our missions, and implement realistic ROE and border patrols. We try to flesh out the ground environment as much as time allows and are experimenting more and more with voiced AIs! Currently we're midway through our first campaign, which is a police action in Georgia as Ossetian and Abkhazian forces attempt to obstruct the construction of a new pipeline in Georgia and unify as the Alanian Republic. Our campaign nights are FRIDAY, 9PM CST with briefing ramping up 30 minutes beforehand. We also have weekly scheduled training nights every Monday at 9PM CST. We just have a few basic requirements to join • Must be 18 years old to join • Must own the F-16, AJS37 Viggen, A-10CII Tank Killer, or Mirage 2000C OR be willing to own LotATC if you'd just like to GCI. • To fly in weekly ops, we require all members to pass a basic type rating in their chosen aircraft. This basically boils down to being able to takeoff, navigate, use the aircraft's most basic weapons, and land. Most people that have been flying the aircraft for about a week should be able to at least stumble through it successfully and you'll have someone who will help you through it. We're more than happy to train you even if you've never flown the module before or are new to DCS! • We have no attendance requirement, but we do require you to RSVP every week to let our dedicated mission makers have an accurate head count so they can tune the campaigns properly. 93rd Tactical Fighter Squadron "Outriders" Commander: Capt. Hex Director of Ops: M. "D20" Shepard Roster Limit: 18 Slots Available: 2 The 93rd Outriders were founded in September of 2020 as an offshoot of Carrier Strike Group 8, comprised of pilots that were looking to fly in Air Force operations with the F-16. The 93rd specializes in SEAD, DEAD and precision strike missions. We currently have 12 pilots on active roster and are always looking for more! 357th Fighter Squadron "Wyverns" Commander: Capt. R. Greyson Director of Ops: Vacant Roster Limit: 12 Slots Available: 4 The 357th Wyverns were founded in October of 2020 shortly after the 93rd. Much could be said about the 357th, but primarily it specializes in BRRRRRTing and supporting our allies armored divisions on the ground. We currently have 10 pilots on active roster and are looking for 2 more highly active individuals to fly weekly with us! 332nd All-Weather Fighter Squadron "Valkyries" Commander: Capt. Kora "Kortana" Director of Ops: N/A Roster Limit: 6 Slots Available: 0 - Recruiting Closed The 332nd Valkyries was founded by our fearless head of mission making Kortana in an effort to bring the joys of Mirage-ing to the masses. There was a noted gap in American time zone based communities for the Mirage and Kortana saw an excellent opportunity to put together a squadron for her favorite aircraft. Although aging and simpler than the F-16, the 332nd has been providing accurate and aggressive CAP for Task Force Valhalla with minimal losses. In the future we expect the 332nd to include the Eurofighter on it's release. F10 Angelholm "Ragnerok" Commander: Capt. K. Sakhir Director of Ops: Capt. R. "Bean" Green Roster Limit: 9 Slots Available: 0 - Recruiting Closed F10 Ragnerok brings the Viggens to a American friendly time zone and is Task Force Valhalla's surprisingly fastest growing squadron. F10 holds the special distinction of providing all of Task Force Valhalla's precision intelligence. Their ELINT missions are the only reason any flight can use a pre-planned target or has knowledge of the precise location of our adversary's mobile SAM network. When not performing ELINT, F10 has proven themselves as the best deep strike package in all of TFV. >>Our Website<< Discord Currently we institute an application process to screen members before they join. We do this because we want to make sure that applicants meet our age requirement, and that our operations actually meet the experience that they're looking for. It's also a good time to ask any questions you might have! Our application process is pretty straight forward: 1. Apply on our website 2.Join our Discord 3. Do 5-10 minute interview with someone from our recruiting team.
  16. Did any of you guys give this one a shot? Thinking about because i'd love some physical feedback for the AB stages but some user experiences would be nice to have. https://www.shapeways.com/product/G4ZVFFBA6/viggen-afterburner-detent-for-warthog-throttle?optionId=110491504&li=marketplace
  • Create New...