stabilator position indicator - ED Forums
 


Notices

Reply
 
Thread Tools Display Modes
Old 03-21-2018, 02:49 PM   #1
kafete
Junior Member
 
Join Date: Mar 2016
Location: Jerez de la Frontera
Posts: 91
Default stabilator position indicator

Hello again guys,

I have another doubt about the stabilator indicator.

Because if you are looking to the EDP the value of the stab indicator some times is different to the MPCD engine page STAB POS indicator.

I have just upload another video to show you.

Kind regards.

https://youtu.be/zFO9kcLjPlI
kafete is offline   Reply With Quote
Old 03-21-2018, 09:42 PM   #2
Eldur
Senior Member
 
Eldur's Avatar
 
Join Date: Dec 2009
Location: On a fluffy cloud above Ponyville
Posts: 2,058
Default

Maybe the MCPD has a floor() while the EDP uses round()

Anyway, the MCPD should show the tenth decimal, like 1.2°. Check 2-20 in the AV-8B-000 NATOPS, pdf page 98.

I don't know how this is in case of the EDP. I guess the output there should work like the thrust gauges in the F-15C or the little gauge inside the RPM gauge of the Mirage, so 1.5° would show the upper half of "1" and the lower half of "2".

https://imgur.com/a/TawlN <- check the H20 gauge... looks like it its slightly below 500, like 426-427ish. The last 0 is static AFAIK.
__________________
Eldur is offline   Reply With Quote
Old 03-22-2018, 06:17 AM   #3
kafete
Junior Member
 
Join Date: Mar 2016
Location: Jerez de la Frontera
Posts: 91
Default

IN ACCORDANCE WITH THE NATOPS nfm000

2.14.1.2.3 Stabilator Position Indicator
Stabilator position is provided on both the EDP and the DDI. The EDP is located on the right side of the main instrument panel and the DDI on the left side (Day Attack aircraft) or either side of the main instrument panel for Radar and Night Attack aircraft. Both indicators display stabilator position in degrees with an arrow to indicate nose up or nose down. Stabilator position on the DDI is displayed on the engine data display and is accessible through the menu display by selecting ENG.

But as I read both indicators have to put the same number at the same time (or it is where I thought) Because as in the paragraf above says, both have the same the "same indicator font", so you can read the sabilator position in both indicators

So they have to put another digit in the Stab pos in the ENG page in the DDI to show as you said avobe.

Last edited by kafete; 03-22-2018 at 01:35 PM.
kafete is offline   Reply With Quote
Old 04-11-2018, 09:31 AM   #4
kafete
Junior Member
 
Join Date: Mar 2016
Location: Jerez de la Frontera
Posts: 91
Default

Remind in next update add the second digit to the Stab indicator in the MPCD, at Engine page.
kafete is offline   Reply With Quote
Old 04-25-2018, 02:19 PM   #5
kafete
Junior Member
 
Join Date: Mar 2016
Location: Jerez de la Frontera
Posts: 91
Default

I have just realize that Razbam didn't update the STAB Position indicator in this Update, could be because it was not clear,

I will put a Pic of the correct digits of the STAB POS Indicator (2 digits istead of 1)

https://ibb.co/jmHOmx
kafete is offline   Reply With Quote
Old 04-26-2018, 03:58 AM   #6
Shrike88
Member
 
Join Date: Dec 2017
Location: Missouri
Posts: 318
Default

+1 Thanks for pointing this out
Shrike88 is offline   Reply With Quote
Old 05-12-2018, 06:27 AM   #7
kafete
Junior Member
 
Join Date: Mar 2016
Location: Jerez de la Frontera
Posts: 91
Default

Zeus67, - CptSmiley Still the same without fix it.... any update about this?

Last edited by kafete; 05-12-2018 at 07:04 PM.
kafete is offline   Reply With Quote
Old 05-23-2018, 03:39 PM   #8
kafete
Junior Member
 
Join Date: Mar 2016
Location: Jerez de la Frontera
Posts: 91
Default

Still without updating the STAB POS Indicator ^^


I will put again the link

https://ibb.co/jmHOmx

You only have to add de decimal digit to the satb position in the Engine display, for example 1.1 1.2 1.3 as I put in the picture.

"Solo hay que añadirle un dígito al Engine Display que tienen que ser 2. Ejemplo 1.1 1.2 1.3" como pone el manual"

Sorry for the text in spanish but could be clearer to Zeus67.

Last edited by kafete; 05-23-2018 at 03:44 PM.
kafete is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT. The time now is 05:16 PM. vBulletin Skin by ForumMonkeys. Powered by vBulletin®.
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.