Sebakogu Posted September 10, 2016 Share Posted September 10, 2016 Hello everyone, sometimes the keys of my warthog throttle doesnt work correctly in the A10-C for example. Is somebody having the same issue? http://www.twitch.tv/sebakogu Link to comment Share on other sites More sharing options...
majapahit Posted September 11, 2016 Share Posted September 11, 2016 DCS has very bad (= tediously slow) button recognition, I have to sometimes repeat 5-8 times before a button shows up. | VR goggles | Autopilot panel | Headtracker | TM HOTAS | G920 HOTAS | MS FFB 2 | Throttle Quadrants | 8600K | GTX 1080 | 64GB RAM| Win 10 x64 | Voicerecognition | 50" UHD TV monitor | 40" 1080p TV monitor | 2x 24" 1080p side monitors | 24" 1080p touchscreen | Link to comment Share on other sites More sharing options...
FeistyLemur Posted September 11, 2016 Share Posted September 11, 2016 I find they seemingly time out in the A-10 module, the switches that is. Like for example sometimes if the EAC and Radar Altimiter switches have been on the whole mission, and I flip them down, they fail to register. So I have to flip them back and forth to get them to. I found the same behavior editing the lua files for other modules to accommodate the WH toggles. After I started using auto hotkey to emulate keyboard commands I never had these issues again. Though I use the A-10 module stock because the controller is premade for it. As for the single press buttons, such as the dms and tms switches, I've never had any problems with them not working. Link to comment Share on other sites More sharing options...
Svend_Dellepude Posted September 11, 2016 Share Posted September 11, 2016 If you start a mission with all switches in their OFF position you wont have this issue. Alternatively you can tick ON ''syncronize buttons at mission start'' in options. When mission starts, DCS reads what switches are in which position when you start a mission. [sIGPIC][/sIGPIC] Win10 64, Asus Maximus VIII Formula, i5 6600K, Geforce 980 GTX Ti, 32 GB Ram, Samsung EVO SSD. Link to comment Share on other sites More sharing options...
majapahit Posted September 11, 2016 Share Posted September 11, 2016 If you start a mission with all switches in their OFF position you wont have this issue. Alternatively you can tick ON ''syncronize buttons at mission start'' in options. When mission starts, DCS reads what switches are in which position when you start a mission. you wish | VR goggles | Autopilot panel | Headtracker | TM HOTAS | G920 HOTAS | MS FFB 2 | Throttle Quadrants | 8600K | GTX 1080 | 64GB RAM| Win 10 x64 | Voicerecognition | 50" UHD TV monitor | 40" 1080p TV monitor | 2x 24" 1080p side monitors | 24" 1080p touchscreen | Link to comment Share on other sites More sharing options...
javelina1 Posted September 11, 2016 Share Posted September 11, 2016 DCS has very bad (= tediously slow) button recognition, I have to sometimes repeat 5-8 times before a button shows up. For the MiG-15, I have the Flaps mapped to my Throttle flap switch. It's hit and miss when activating this switch if the flaps will actually deploy. I've experienced this a few times. Not sure why... MSI MAG Z790 Carbon, i9-13900k, NH-D15 cooler, 64 GB CL40 6000mhz RAM, MSI RTX4090, Yamaha 5.1 A/V Receiver, 4x 2TB Samsung 980 Pro NVMe, 1x 2TB Samsung 870 EVO SSD, Win 11 Pro, TM Warthog, Virpil WarBRD, MFG Crosswinds, 43" Samsung 4K TV, 21.5 Acer VT touchscreen, TrackIR, Varjo Aero, Wheel Stand Pro Super Warthog, Phanteks Enthoo Pro2 Full Tower Case, Seasonic GX-1200 ATX3 PSU, PointCTRL, Buttkicker 2, K-51 Helicopter Collective Control Link to comment Share on other sites More sharing options...
WildBillKelsoe Posted September 11, 2016 Share Posted September 11, 2016 Too many modules? SSD on? Sent from my SM-T231 using Tapatalk AWAITING ED NEW DAMAGE MODEL IMPLEMENTATION FOR WW2 BIRDS Fat T is above, thin T is below. Long T is faster, Short T is slower. Open triangle is AWACS, closed triangle is your own sensors. Double dash is friendly, Single dash is enemy. Circle is friendly. Strobe is jammer. Strobe to dash is under 35 km. HDD is 7 times range key. Radar to 160 km, IRST to 10 km. Stay low, but never slow. Link to comment Share on other sites More sharing options...
BitMaster Posted September 11, 2016 Share Posted September 11, 2016 Never had that on mine tbh. The setup-gui for controls is slow tho, there it is normal to have to flip or press any Hotas control multiple times to register, but never in game. All but 3 modules installed, dcs has its own ssd Gesendet von iPhone mit Tapatalk Gigabyte Aorus X570S Master - Ryzen 5900X - Gskill 64GB 3200/CL14@3600/CL14 - Asus 1080ti EK-waterblock - 4x Samsung 980Pro 1TB - 1x Samsung 870 Evo 1TB - 1x SanDisc 120GB SSD - Heatkiller IV - MoRa3-360LT@9x120mm Noctua F12 - Corsair AXi-1200 - TiR5-Pro - Warthog Hotas - Saitek Combat Pedals - Asus PG278Q 27" QHD Gsync 144Hz - Corsair K70 RGB Pro - Win11 Pro/Linux - Phanteks Evolv-X Link to comment Share on other sites More sharing options...
Sebakogu Posted September 12, 2016 Author Share Posted September 12, 2016 I think it's bugged. Same issues at F5-E! DCS thinks keys are double binded (but i didnt double bind any key). I hope they will fix it soon. In Mp keys work fine until you are airborn. Then the issues start. No flaps, no communication menue, no mfd changing for example. http://www.twitch.tv/sebakogu Link to comment Share on other sites More sharing options...
Recommended Posts