ohyeah2389 Posted August 29, 2020 Share Posted August 29, 2020 Hello, Since DCS doesn't allow you to bind separate commands for switch press and release, the Special For Joystick commands are essential. However, I find it confusing that while the roll AP switch has them, the pitch AP does not; similarly, the Master Arm has one, but the Laser Arm does not. Please add commands for these switches (or allow us to bind keypress and keyrelease to different commands ourselves). Gigabyte GA-Z170X-Gaming 7, i5 6600K @3.5ghz, GTX 1070, 16GB ram, Windows 10 Home x64 https://pcpartpicker.com/b/JH9J7P Modules: A-10C, FC3, F/A-18C, UH-1H, MI-8MTV2, Ka-50, SA342, AJS-37, AV-8BNA, M-2000C, MiG-21, F-14A/B, JF-17, F-16C, Supercarrier Maps: Caucasus, NTTR, Persian Gulf Awaiting: DCS: F-15E Link to comment Share on other sites More sharing options...
Delareon Posted August 30, 2020 Share Posted August 30, 2020 while its not hard to do them on your own, its a bit of a pain to restore them after every update since the file gets overwritten even if there is no change. +1 Link to comment Share on other sites More sharing options...
jonsky7 Posted September 24, 2020 Share Posted September 24, 2020 You can add these two lines in Dcs World\Mods\aircraft\F-16C\Input\F-16C\joystick\default.lua { down = control_commands.ApPitchAlt_EXT, up = control_commands.ApPitchAlt_EXT, cockpit_device_id = devices.CONTROL_INTERFACE, value_down = 1.0, value_up = -1.0, name = _('Autopilot PITCH Switch - ALT HOLD / A/P OFF (Multi-pos switch)'), category = {_('Instrument Panel'), _('FLCS')}}, { down = control_commands.ApPitchAtt_EXT, up = control_commands.ApPitchAtt_EXT, cockpit_device_id = devices.CONTROL_INTERFACE, value_down = -1.0, value_up = 1.0, name = _('Autopilot PITCH Switch - ATT HOLD / A/P OFF (Multi-pos switch)'), category = {_('Instrument Panel'), _('FLCS')}}, Link to comment Share on other sites More sharing options...
TOViper Posted September 29, 2020 Share Posted September 29, 2020 (edited) Can the middle line be correct (which is currently DCS standard): {down = control_commands.ApPitchAlt_EXT, up = control_commands.ApPitchAlt_EXT, cockpit_device_id = devices.CONTROL_INTERFACE, value_down = 1.0, value_up = 0.0, name = _('Autopilot PITCH Switch - ALT HOLD'), category = {_('Instrument Panel'), _('FLCS')}}, {down = control_commands.ApPitchAlt_EXT, cockpit_device_id = devices.CONTROL_INTERFACE, value_down = -1.0, name = _('Autopilot PITCH Switch - A/P OFF'), category = {_('Instrument Panel'), _('FLCS')}}, {down = control_commands.ApPitchAtt_EXT, up = control_commands.ApPitchAtt_EXT, cockpit_device_id = devices.CONTROL_INTERFACE, value_down = -1.0, value_up = 0.0, name = _('Autopilot PITCH Switch - ATT HOLD'), category = {_('Instrument Panel'), _('FLCS')}}, I think the -1.0 for value_down can't be correct ... any thoughts about it? Edited September 29, 2020 by TOViper Visit https://www.viggen.training ...Viggen... what more can you ask for? my computer: AMD Ryzen 5600G | NVIDIA GTX 1080 Ti OC 11GB | 32 GB 3200 MHz DDR4 DUAL | SSD 980 256 GB SYS + SSD 2TB DCS | TM Warthog Stick + Throttle + TPR | Rift CV1 Link to comment Share on other sites More sharing options...
Frederf Posted September 29, 2020 Share Posted September 29, 2020 while its not hard to do them on your own, its a bit of a pain to restore them after every update since the file gets overwritten even if there is no change. +1 If new commands could somehow be written in the .diff.lua it would make it more practical to create and persist custom controls from version to version. Link to comment Share on other sites More sharing options...
Delareon Posted September 30, 2020 Share Posted September 30, 2020 If new commands could somehow be written in the .diff.lua it would make it more practical to create and persist custom controls from version to version. That would be awesome. But currently i dont think it works that way. Link to comment Share on other sites More sharing options...
Baz000 Posted October 1, 2020 Share Posted October 1, 2020 adding landing gear so I can use my thrustmaster warthog base switches would be great Link to comment Share on other sites More sharing options...
Griffon345 Posted October 1, 2020 Share Posted October 1, 2020 How about including 'press' and 'release' as modifiers for all setups. This would satisfy many threads I have researched as well as rounding out perfect native support for every controller available (sic). I admit I have no idea how easy this is to do. Sent from my SM-G975F using Tapatalk Link to comment Share on other sites More sharing options...
Recommended Posts