-Hammer- Posted September 17, 2015 Share Posted September 17, 2015 Hello you Cockpit Builders out there! I want to join the club, but run into my first problem :cry: I tried to connect a three way switch (ON-ON-ON) for the IFFCC Switch (OFF-TEST-ON) and bought this switch: APEM 644H/2 (DPDT) http://eu.mouser.com/search/ProductDetail.aspx?Apem%2f644H-2%2f&qs=%2fs1LKTamv0z1Fm2vV5nWZw== to work with a Leo Bodnar BBI-32 Board. ON-ON and ON-OFF-ON switches are working like they should It has 6 Pins and I have no clue how to wire them.... The Pins are numbered like this: Top Row: A1 | B1 Middle Row: A2 | B2 Upper Row: A3 | B3 Is this the right switch for my project? Thank you for your help!:thumbup: Windows 10 | i7-8700K@5GHz | 2080 Ti | Intel Z370 Chipset | 32GB RAM@1866 MHz | SSD: Samsung 850 EVO 1TB| Thrustmaster Warthog HOTAS w. FSSB R3 Mod | Saitek Switch Panel + Radio Panel + Multi Panel + FIP + Flightpanels Software | MFG_Crosswind | TrackIR5 | TM Cougar MFD Pack | Obutto R3volution | 1 x LG38 | GAMETRIX KW-908 JETSEAT Link to comment Share on other sites More sharing options...
debolestis Posted September 17, 2015 Share Posted September 17, 2015 Like this 1 - Debolestis' Shapeways store - Debolestis' Facebook page - Suncom SFS and Talon restoration and mods - Cougar replacement gimbal Link to comment Share on other sites More sharing options...
cichlidfan Posted September 17, 2015 Share Posted September 17, 2015 If all three positions of the IFFCC switch have separate commands within DCS (I don't recall at the moment) then you should with A1-B1 to one Bodnar (switch and ground) and do the same for the other two pairs of contacts (keeping the like numerals together). ASUS ROG Maximus VIII Hero, i7-6700K, Noctua NH-D14 Cooler, Crucial 32GB DDR4 2133, Samsung 950 Pro NVMe 256GB, Samsung EVO 250GB & 500GB SSD, 2TB Caviar Black, Zotac GTX 1080 AMP! Extreme 8GB, Corsair HX1000i, Phillips BDM4065UC 40" 4k monitor, VX2258 TouchScreen, TIR 5 w/ProClip, TM Warthog, VKB Gladiator Pro, Saitek X56, et. al., MFG Crosswind Pedals #1199, VolairSim Pit, Rift CV1 :thumbup: Link to comment Share on other sites More sharing options...
-Hammer- Posted September 17, 2015 Author Share Posted September 17, 2015 That was quick, but @cichlidfan: The IFFCC has separate commandos but A1-B1, etc. is not working. @debolestis: Thanks for the picture, so in my case A1 is Top Left and B6 is bottom right corner. This is what I am going to do: 1. Connect A1 with B6 (check) 2. Where do I but the ground wire(s) + the other 3 wires? I am completely lost Windows 10 | i7-8700K@5GHz | 2080 Ti | Intel Z370 Chipset | 32GB RAM@1866 MHz | SSD: Samsung 850 EVO 1TB| Thrustmaster Warthog HOTAS w. FSSB R3 Mod | Saitek Switch Panel + Radio Panel + Multi Panel + FIP + Flightpanels Software | MFG_Crosswind | TrackIR5 | TM Cougar MFD Pack | Obutto R3volution | 1 x LG38 | GAMETRIX KW-908 JETSEAT Link to comment Share on other sites More sharing options...
debolestis Posted September 17, 2015 Share Posted September 17, 2015 Sorry I thought you have BU0836A. I don't know if this will work but try. You forget diodes. Connect Column 1 to B1 (for example on you board), row 1 to ground next to B1. Connect Column 2 to B2 on board row 2 to ground next to B2. Connect Column 1 to B3 also. Row 2 to ground next to B3. I have never worked with this board, probably it is not necessary to connect all the grounds to board, but just in case... If all grounds are real grounds this probably won't work. Probably could have double press. Please test and let us know. - Debolestis' Shapeways store - Debolestis' Facebook page - Suncom SFS and Talon restoration and mods - Cougar replacement gimbal Link to comment Share on other sites More sharing options...
-Hammer- Posted September 17, 2015 Author Share Posted September 17, 2015 I get double presses in windows, its like this: 1 2 1+3 and DCS just recognizes Button 1 and Button 2 Windows 10 | i7-8700K@5GHz | 2080 Ti | Intel Z370 Chipset | 32GB RAM@1866 MHz | SSD: Samsung 850 EVO 1TB| Thrustmaster Warthog HOTAS w. FSSB R3 Mod | Saitek Switch Panel + Radio Panel + Multi Panel + FIP + Flightpanels Software | MFG_Crosswind | TrackIR5 | TM Cougar MFD Pack | Obutto R3volution | 1 x LG38 | GAMETRIX KW-908 JETSEAT Link to comment Share on other sites More sharing options...
Sokol1_br Posted September 17, 2015 Share Posted September 17, 2015 (edited) If the GND are common in BBI32 you can try: imagur The red trace is a wire bridge between A3 and B2. GND is connected to A2. BBI32 button 1 = A2+A1 BBI32 button 2 = A2+B1 BBI32 button 3 = A2+B3 Edited September 18, 2015 by Sokol1_br 2 Link to comment Share on other sites More sharing options...
-Hammer- Posted September 19, 2015 Author Share Posted September 19, 2015 Thank you guys for all the input :thumbup: My first switch is finally working (only about 300 to go :)), I´m so happy But I´m getting old and read the B numbers wrong.....:doh: (sorry) This is how the APEM 644 H/2 Switch works (The prints on the switch are on the left hand side) Top Row: A1 | B4 Middle Row: A2 | B5 Bottom Row: A3 | B6 Wire Bridge: A2 <-> B6 Ground Wire (with the BBI 32 I just need one ground wire): B5 BBI32 button 1 = A1 BBI32 button 2 = A3 BBI32 button 3 = B4 Windows 10 | i7-8700K@5GHz | 2080 Ti | Intel Z370 Chipset | 32GB RAM@1866 MHz | SSD: Samsung 850 EVO 1TB| Thrustmaster Warthog HOTAS w. FSSB R3 Mod | Saitek Switch Panel + Radio Panel + Multi Panel + FIP + Flightpanels Software | MFG_Crosswind | TrackIR5 | TM Cougar MFD Pack | Obutto R3volution | 1 x LG38 | GAMETRIX KW-908 JETSEAT Link to comment Share on other sites More sharing options...
Recommended Posts