Easy Monitor Configurator

Thanks G00dnight I just did the update and your walk though worked.

Thanks again.

I just noticed that when I disable MFCDs they still render in A10C.

Does anyone else have this happening? My frames rate has dropped a lot because I am running them on seperate monitors as well.

Thnx for this great app. However when does the final version with fc3 support will be released?

We don't know if Iceman is still working on it..but live in hope he is waiting for EDGE to arrive..

Any one know how to Adjust for the 1.2.11 BETA, My EMC is not directed to the right path/directory. Is there an easy way to switch it between the official and the BETA versions? EMC will work on 1.2.10 only....driving me nuts because certain servers are running the beta and some are not.

I dont know if putting the same info int the beta registry entry or even if there is a separate beta reg entry I don't use it. if you read back in this thread and then look in your reg you may be lucky also i dont know how you would get it to see both lots unless you had 2 installs of EMC.

Yeah its a complex system when you've have a few rums....I deleted DCS and EMC, update came out few days ago so just went and downloaded it all over again. I did however have to make some new registry edits, like Create A-10C folder under DCS cause now its getting lazy and not writing these entry"s apon install...All good now just takes some tweaking as always.

Then EDGE will come out and we'll do it all over again no doubt, but then again might be old and grey by then...

Hi.

I downloaded and installed this software. After run, it started to open Paypal page for Icemaker, but it was like a burst movement, opened too much page in a second!

Then, my PC was locked and had to reset!

I uninstalled this! :mad:

Hi.

 

I downloaded and installed this software. After run, it started to open Paypal page for Icemaker, but it was like a burst movement, opened too much page in a second!

 

My PC locked and had to restart.

 

I uninstalled this!

I haven't used it in a long time, but that fact that he never fixed that is absolutely unbelievable. :doh:

Btw, it only happens the first time you run it (or used to).

It was never fixed because Icemaker stopped developing it as it was getting silly with every update changing so much. shame coz it is really good. There is an alternative in development.

http://forums.eagle.ru/showthread.php?t=125728

early days yet though but it looks good.

Does this software still work properly on version 1.2.16? It says me that it can't found the DCS World directory.

Anyway, would be possible with it showing the HSI on a separate screen?

no and no.

no and no.

Thank you.

Easy Monitor Works great for me through all versions. Still using today

A better option will be UMFCD when it is finished exports will be available with out having to set your 2nd screen as part of the overall resoulution in game so saving a lot of processing power.

@ HellsBells yes it will work as you go on until you reinstall your comp then if you want it to work you will have to hack your registry which is a bit above most people I see asking questions on here, As if not done correctly can kill the whole computer so requiring a reinstall so going back to square one.

Will the caution panel be offered to display on a single display? The A10- C caution panel.

Any bites. Maybe change lures:music_whistling:

Gracias Amigo...http://forums.eagle.ru/images/smilies/smile.gif

Thanks for the intel on EASY MONITOR CONFIGURATOR...You are my favorite TACO!!

hmmm... what am I doing wrong? Been away from A-10C for a bit, and just jumping back in. (Had changed my Vid settings along the way)

Using EMC and Helios. My Helios gauges display just fine. Using TM MFD's which are on a 2nd display.

Primary is a 1920 x 1080, secondary is a 1600 x 900.

My Heilos gauges display just fine on the secondary. Everything is where I want. I've used EMC for setting my MFD's. And they look great positioned within the TM MFD frame.

Every time I start up DCS, fly the A-10C, it shifts the MFD extract (via EMC) down to the bottom of my secondary display.

Here's my camera lua:

_ = function(p) return p; end;

name = _('this one dad, Screen');

Description = 'two monitor configuration'

Viewports =

{

Center =

{

x = 0;

y = 0;

width = 1920;

height = 1080;

viewDx = 0;

viewDy = 0;

aspect = 1920/1080;

}

}

GUI=

{

x = 0 ;

y = 0 ;

width = 1920 ;

height = 1080 ;

}

ED_A10C_CMSP =

{

x = 2441;

y = 8;

width = 270;

height = 60;

}

ED_A10C_RIGHT_MFCD =

{

x = 3087;

y = 69;

width = 392;

height = 392;

}

ED_A10C_LEFT_MFCD =

{

x = 1960;

y = 65;

width = 386;

height = 386;

}

UIMainView = Viewports.Center

Any suggestions?

TIA,

-Jav

find the latest export lua from whatever his name is in User files?

:)

http://forums.eagle.ru/showthread.php?p=2503960#post2503960

No joy... using 1.2x DCS, (not the beta 1.5)

squared away now.... (better change management and naming convention for my .lua's! :-) ) working good now, show love again for the A-10C, (as you should!)

Another fabulous thread that is maturing well; congrats to all hands!