komemiute Posted May 4, 2014 Share Posted May 4, 2014 I managed, after arduous and rigorous testing, to break on purpose (eh-rm) the tail boom. What surprised me was that the Hip was, albeit spinning quite strongly, incredibly stable. I could handle altitude and general direction with little problem... is that really so? Link to comment Share on other sites More sharing options...
Maulkin Posted December 13, 2014 Share Posted December 13, 2014 A track would be useful. --Maulkin Windows 10 64-bit - AMD Ryzen 9 5900X @ 3.7 GHz - 32 GB DDR4 3600MHz RAM - EVGA FTW3 RTX 3080 - Asus Crosshair VIII Hero motherboard - Samsung EVO Pro 1 TB SSD - TrackIR 4 Pro - Thrustmaster Warthog - Saitek rudder pedals - Lilliput UM-80/C with TM Cougars Link to comment Share on other sites More sharing options...
Cibit Posted December 13, 2014 Share Posted December 13, 2014 everytime I break the tail boom off I spin madly i5 8600k@5.2Ghz, Asus Prime A Z370, 32Gb DDR4 3000, GTX1080 SC, Oculus Rift CV1, Modded TM Warthog Modded X52 Collective, Jetseat, W10 Pro 64 [sIGPIC][/sIGPIC] Adding JTAC Guide //My Vid's//229th AHB Link to comment Share on other sites More sharing options...
dali Posted November 12, 2015 Share Posted November 12, 2015 I broke the tail during landing and it seems that Mi-8 entered a lifting spiral with locked speed (24 km/h). Link to comment Share on other sites More sharing options...
simapajik Posted April 10, 2017 Share Posted April 10, 2017 (edited) Hello to everybody Modest request: Mi-8 diverge at speed 250 km / h, the rotor pitch in degrees 11 to 12 When you pull the lever cyclic control for himself and helicopter nose starts to rise, torn off the back of the tail rotor balancing. I feel that there is a change in the strength of the module. Before that, the tail not keep. Is that right or wrong? The helicopter must withstand greater strength for sure. Previous versions did not do this. Edited April 10, 2017 by simapajik <White Tiger> [sIGPIC][/sIGPIC] Link to comment Share on other sites More sharing options...
simapajik Posted April 10, 2017 Share Posted April 10, 2017 The manual says that the maximum rotor pitch in degrees 12. When I can set the maximum rotor pitch of 12 degrees, why is torn tail. <White Tiger> [sIGPIC][/sIGPIC] Link to comment Share on other sites More sharing options...
Pocket Sized Posted April 11, 2017 Share Posted April 11, 2017 The manual says that the maximum rotor pitch in degrees 12. When I can set the maximum rotor pitch of 12 degrees, why is torn tail. In flight, the tail will break upon exceeding 3 Gs (indicated by the small gauge on top of the front panel). This is probably what happened when you pitched up. DCS modules are built up to a spec, not down to a schedule. In order to utilize a system to your advantage, you must know how it works. Link to comment Share on other sites More sharing options...
simapajik Posted April 11, 2017 Share Posted April 11, 2017 In flight, the tail will break upon exceeding 3 Gs (indicated by the small gauge on top of the front panel). This is probably what happened when you pitched up. Yes ... it looks like I have to keep an eye pointer accelerometer. Very good note. Thank you.. :thumbup: <White Tiger> [sIGPIC][/sIGPIC] Link to comment Share on other sites More sharing options...
BitMaster Posted May 29, 2017 Share Posted May 29, 2017 Tbh, I have broken MANY tail booms and often I manage to land the bird while spinng & spinning. I have no idea if this was possible in RL, I actually doubt it. Here's how I manage to do it. 1. LOOK at your VSI !!! stabilize it 2. fight the up/down oscillating and compensate as much as possible, it is possible 3. GENTLY set the bird to the ground with 1-2m/sec on your VSI 4. repair ;) Gigabyte Aorus X570S Master - Ryzen 5900X - Gskill 64GB 3200/CL14@3600/CL14 - Asus 1080ti EK-waterblock - 4x Samsung 980Pro 1TB - 1x Samsung 870 Evo 1TB - 1x SanDisc 120GB SSD - Heatkiller IV - MoRa3-360LT@9x120mm Noctua F12 - Corsair AXi-1200 - TiR5-Pro - Warthog Hotas - Saitek Combat Pedals - Asus PG278Q 27" QHD Gsync 144Hz - Corsair K70 RGB Pro - Win11 Pro/Linux - Phanteks Evolv-X Link to comment Share on other sites More sharing options...
Recommended Posts