Simpit Software from SDA

We do not duplicate anything today. I think it still works like it was back then. Unfortunately. I had a bit of a hunch that I would not have to change the DCS scripts to get those expenses. That worked. Unfortunately in the version 2.5 no more.

your reply prove me that my question is not clear.

In Ikarus, the RWR if just a clear frame with no DATA. The DATA needs to comes from DCS like the MFCD. so how to make RWR DATA "under" the Ikasus so it can be seen thruth ?

see the fisrt picture : https://forums.eagle.ru/showthread.php?t=70716

this is V1.1.1.1 old

I am loog for a new and beter way to do it

I am sure you are doing it but my question is not clear (bad english level...)

Thanks for your time

You need a hole in the Ikarus copit. We use png - files. This makes it possible to define a transperency. Also a semitrancy. Does that answer your question?

I have to take a closer look tomorrow ... let's see .. I'll contact you. It would be nice if there was another way.

You need a hole in the Ikarus copit. We use png - files. This makes it

possible to define a transperency. Also a semitrancy. Does that answer your question?

I need the green info to show up in the monitor then I will be able to start Ikarus over it

Can you see. I need this top center the little "A"

@JAT

Problems found for "UHF radio mode select" and "Tacan mode select". :thumbup:

@raymondabel

You have to understand that we can not offer customized solutions. That would exceed my time. Please try it yourself. It's not that hard either.

There are some forums that have already dealt with this. You have to make changes to the Lua - files in DCS. Just search. This is always necessary with the RWR. Unfortunately.

@raymondabel

 

You have to understand that we can not offer customized solutions. That would exceed my time. Please try it yourself. It's not that hard either.

probably all Ikarus user had done the modification yet.

AN_ALR69V_init.lua needs to be modify

C:\Program Files\eagle dynamics\DCS World\Mods\A-10C - Instrument Export\Mods\aircraft\A-10C\Cockpit\scripts\AN_ALR69V\indicator\AN_ALR69V_init.lua

and

C:\Program Files\eagle dynamics\DCS World\Config\MonitorSetup

Very good raymondabel. Remember, if an update is installed, then your changes are overwritten again. Make a backup. :smilewink:

Very good raymondabel. Remember, if an update is installed, then your changes are overwritten again. Make a backup. :smilewink:

:)

is it possible to have yours AN_ALR69V_init.lua for A-10C yours MonitorSetup *.lua file assoated witj it then?

mine is for V1.1.1.1 so it must have gone thout a lot of changes since then

Thanks for your time

Ray

Aha, that's great !

@JAT

I upload Developer Version 1.4.5.3n for M-2000C bug fixes and lights panel and F/A-18 compass. McMicha is still working on the displays.

There are also 2 supplemented lua files. Please copy accordingly.

Great improvement, congrats !

Here are my remarks:

- UHF mode switch still return to the default position by itself

- Barometric pressure calibration knob stop turning after some clics

- All lights must be a 3 position switch

- Hydraulique emergency pump switch must be a 3 position switch

- Pitot heat switch must be down as default position

You are near the end on this i think :)

I am only finished when you are satisfied. We'll get that very soon.

I found what I was looking for:

https://forums.eagle.ru/showthread.php?t=70716&page=62

Export - All Viewports.rar

I am trying to put ikarus at the second screen but i can not.Any can help?

I am trying to put ikarus at the second screen but i can not.Any can help?

for A-10c but it will probably works for all

open Ikarus

click configutration

find front panel

find "Pos X" then change zero" for what you need

find "Pos Y" then change zero" for what you need

Save

refresh

wala

for A-10c but it will probably works for all

 

open Ikarus

click configutration

find front panel

find "Pos X" then change zero" for what you need

find "Pos Y" then change zero" for what you need

Save

refresh

wala

it is already to zero both.i should change ip to 192.160.0.192?

it is already to zero both.i should change ip to 192.160.0.192?

IP adress as nothig to do with screen position

it should be let at 127.0.0.1 AFAIAK

it is already to zero both.i should change ip to 192.160.0.192?

welll

if you read what I wrote

CHANGE the zero to an othe digit

so if you have 2 screen lone over the other

Pos Y is set to 1080 in my case.

Pl take time to READ when someone take the time to reply to you.

If you do not undersand then say: "your english level is poor and I do not undersatnd"

That will be better

welll

if you read what I wrote

CHAGE the zero to an othe digit

so if you have 2 screen lone over the other

Pos Y is set to 1080 in my case.

 

Pl take time to READ when someone take the time to reply to you.

If you do not undersand then say: "your english level is poor and I do not undersatnd"

That will be better

It was a mistake.I was reading fast i did not understand what you said.I did what you say but just the panel get smaller.Both windows DCS and IKARUS is at the same screen,I make something wrong but i can not find it.I choosed panel 1 nad 2.

It was a mistake.I was reading fast i did not understand what you said.I did what you say but just the panel get smaller.Both windows DCS and IKARUS is at the same screen,I make something wrong but i can not find it.I choosed panel 1 nad 2.

be sure you modify Pos X and Pos Y

nor Width or Height...

:)

Also, yau have to finf the main panel. On A-10C it is call Front Panel.

Witch plane would you like to modify?

Question: Do you have 2 sreens or you try to have DCS and Ikarus on the same screen?

Yes i do that i am sure :)

allo

little "bugs" I found it the A-10C profile:

mostly all the same thing

3 way switch are not set properly when you start the profile.

AHCP - Turn On/Off/Test IFFCC; DCSID 384 at test should be at off

all CMSP 3way switch should be at off but start at on

Not clear withLand Taxi Lights DCSID 655 but should start at off.

I try to find a way to fix it myself but I am no programer at all.

Just an happy user.

One thing, I have to set those each time because I notice that when I do not do it, DCS freese. I can not make a clear relation one on one (Univeral Radio)+Ikarus= DCS freese yet to help to find what is wrong.

Thanks for your time

Ray

@Ray

Thanks for the good bug report. I will release a new version soon.

Just one thing.

You do not have to be a programmer. It just needs to be configured accordingly. Anyone who has read our wiki should be able to do that. Of course, I'm doing this now, so that everyone has something of it. Please send more reports and take a closer look. Thank you.

The A-10C was our first project with Ikarus. Since then a lot has changed. :thumbup: