Removed

looking forward for this project

I Find myself Flying through the mountains in the AFM Demo more than anything else actually...

I Find myself Flying through the mountains in the AFM Demo more than anything else actually...

very nice WIP keep walking , i am sure the DCS will help on that

if you need help or beta testing give me a "call"

Regards

I Find myself Flying through the mountains in the AFM Demo more than anything else actually...

Can the latest mod ver. 0.3 be smoothly used in 1.2.6?

I put the module to 1.2.6 Mods/aircrafts and I can sit into the cockpit

however, I can not control the plane even it starts in the air.

no response for any key: left, right ,up, down, or page up/down ....

then f16 down to the ground

Thanks guys that is all correct. I'm not 3d modeler, or artist, I'm just an aero engineer that likes the take my work home with me :)

Hi,

first thanks for your sharing.

I tried it with 1.2.6, however, i cannot control the plane, no response for any key. The plane starts in the air.

I want to know how to compile this project under win? I think it is a visual studio project.

I only have g++/vim/makefile experience for project under linux.

Thanks

It's a visual studio project yes. And for not controlling the aircraft, you did set up your controls for it, right?

It's a visual studio project yes. And for not controlling the aircraft, you did set up your controls for it, right?

I think so. Before flying it, I went to Option, and went through all keys of F-16Demo. I just used keyboard, not sticks. Then in the game, no response for any key.

My friend also tried it under 1.2.6, same result

I will test tonight, but Im pretty sure it works fine in 1.2.6

I will test tonight, but Im pretty sure it works fine in 1.2.6

My 1.2.6 is clean version. My friend's as well. I will try it later.

I have recompiled the FM using VS 2010 and it does not work either. Same result.

Can I say it is lua issue?

fresh download and install, it's working fine here.

Only issue is the lack of AoA limiting, so if I pull too hard below 350ish it just goes into a spin.

And the landing gear.

Do the landinggear extend at all?

under a certain altitude and speed i think it what it was set at.

also if needed, I exported the F-16C_Blk20 Pit, might feel more accurate,

I need to script a HUD or something lol.

fresh download and install, it's working fine here.

 

Only issue is the lack of AoA limiting, so if I pull too hard below 350ish it just goes into a spin.

 

And the landing gear.

Did you use keyboard or joystick?

I used keyboard, and did not try joystick.

After sitting in the cockpit (starts in the air), should I press any key to start engine or like rshift+l to engage avionic? Such that control can be enabled?

I just installed DCS 1.2.6 and the fresh download on another computer. Failed to control again (Now 3 fresh DCS126 and F-16 install on 3 computers)

For 3000 height, 600 speed (metric), the airplane moves forward, then keeps on falling. No respond on left, right, up, down or page up/down

What else microsoft vc++ library does it require?

I need to script a HUD or something lol.

I'll take an F-16 HUD, thanks. :P

What else microsoft vc++ library does it require?

Hmm, make sure you're running the very latest Visual C++ Redistributable package. I had a similar problem back when we were first working on our EFM and it would just fall out of the sky slowly with no control.

Hmm, make sure you're running the very latest Visual C++ Redistributable package. I had a similar problem back when we were first working on our EFM and it would just fall out of the sky slowly with no control.

I installed the VC++ redist package that is supplied by DCS installer package. So it should be the latest, right?

I'm going to upload two trks.

I use Joystick... never tried with keyboard.

I'll take an F-16 HUD, thanks. :P

I'd have to do it step by step, basic hud, working, then start adding stuff.

But if the underlying systems arent there it prolly wouldnt work right.

It works now.

Joystick flies well, while no response to keyboard up,down,right,left

Keyboard inputs for flight control in AFM aircraft have to be programmed into the flight model code. The code includes a function to read the joystick, but not to read keyboard inputs and transform those inputs into axis movements.

Keyboard inputs for flight control in AFM aircraft have to be programmed into the flight model code. The code includes a function to read the joystick, but not to read keyboard inputs and transform those inputs into axis movements.

Thanks, and I just realized it.

BTW, do you know where to download the template code project for flight model?

the data an stuff should have been part of the 300 mb download.

the data an stuff should have been part of the 300 mb download.

Thanks