Zooker Posted December 3, 2019 Share Posted December 3, 2019 Is there a trick to updating the YY location from the ME bullseye when in an other-than-cold-start jet? I keep moving my own position, a steerpoint, or nothing happens when inputting new YY coordinates. VF-111 Sundowners [sIGPIC][/sIGPIC] Carrier Group 1 - Battlegroup Delta Beware the lessons of a fighter pilot who would rather fly a slide rule than kick your ass! -Commander Ron "Mugs" McKeown, USN Commander, U.S. Navy Fighter Weapons School 2 Victories, Vietnam Link to comment Share on other sites More sharing options...
IronMike Posted December 4, 2019 Author Share Posted December 4, 2019 Is there a trick to updating the YY location from the ME bullseye when in an other-than-cold-start jet? I keep moving my own position, a steerpoint, or nothing happens when inputting new YY coordinates. The easiest way is to have an F10 marker, and Jester selects that as YY. If you yourself put in a new YY, you need to make sure that no waypoint or anything else is hooked. If the coord entry moves own position or waypoints, then it means they are hooked when they should not be. Heatblur Simulations Please feel free to contact me anytime, either via PM here, on the forums, or via email through the contact form on our homepage. http://www.heatblur.com/ https://www.facebook.com/heatblur/ Link to comment Share on other sites More sharing options...
QuiGon Posted December 4, 2019 Share Posted December 4, 2019 The easiest way is to have an F10 marker, and Jester selects that as YY. If you yourself put in a new YY, you need to make sure that no waypoint or anything else is hooked. If the coord entry moves own position or waypoints, then it means they are hooked when they should not be. Hmm, dumb question: How to unhook/deselect own position? Intel i7-12700K @ 8x5GHz+4x3.8GHz + 32 GB DDR5 RAM + Nvidia Geforce RTX 2080 (8 GB VRAM) + M.2 SSD + Windows 10 64Bit DCS Panavia Tornado (IDS) really needs to be a thing! Link to comment Share on other sites More sharing options...
IronMike Posted December 4, 2019 Author Share Posted December 4, 2019 Hmm, dumb question: How to unhook/deselect own position? Ha, good question, hehe. Did you try just hooking something else instead? Or half action again into the blank space before going full action? Heatblur Simulations Please feel free to contact me anytime, either via PM here, on the forums, or via email through the contact form on our homepage. http://www.heatblur.com/ https://www.facebook.com/heatblur/ Link to comment Share on other sites More sharing options...
QuiGon Posted December 4, 2019 Share Posted December 4, 2019 Ha, good question, hehe. Did you try just hooking something else instead? Or half action again into the blank space before going full action? Not specifically for the purpose to deselect/unhook own pos, but I've often performed half action into the blank space for other reasons, and IIRC OWN POS always stays selected on the CAP, no matter what. The only way to deselect it that I know of is to select a waypoint, but that's also not permitable for navgrid position entry as you stated earlier in this thread. So I wonder: How can I not have either a WP or OWN POS selected on the CAP in order to enter the NAVGRID position? Intel i7-12700K @ 8x5GHz+4x3.8GHz + 32 GB DDR5 RAM + Nvidia Geforce RTX 2080 (8 GB VRAM) + M.2 SSD + Windows 10 64Bit DCS Panavia Tornado (IDS) really needs to be a thing! Link to comment Share on other sites More sharing options...
IronMike Posted December 4, 2019 Author Share Posted December 4, 2019 (edited) Did you try just half action -> release? If that doesn't work, it could be a bug, I need to ask gyrovague. EDIT: ok, I just talked to Naquaii, according to how we implemented it and how it is according to our docs, you cannot unhook own a/c. however it does not have to be unhooked, only waypoints etc. when in nav grid and ground stab you can enter the data for navgrid even if it displays own a/c. (I think I said own a/c before, that was wrong if I did.) Edited December 4, 2019 by IronMike Heatblur Simulations Please feel free to contact me anytime, either via PM here, on the forums, or via email through the contact form on our homepage. http://www.heatblur.com/ https://www.facebook.com/heatblur/ Link to comment Share on other sites More sharing options...
QuiGon Posted December 4, 2019 Share Posted December 4, 2019 Did you try just half action -> release? If that doesn't work, it could be a bug, I need to ask gyrovague. Yeah, that's what I was talking about. As i said, I haven't tried it specifically for the purpose of deselecting OWN POS, but for other purposes. I can not remember having ever seen OWN POS getting deselected by HCU half action though. Half action definitely unhooks WPs and other hooked symbology on the TID, but I'm not sure if it also deselects them on the CAP. I will have to deliberately test deselecting OWN POS by pressing HCU half action in order to give a verified answer. Intel i7-12700K @ 8x5GHz+4x3.8GHz + 32 GB DDR5 RAM + Nvidia Geforce RTX 2080 (8 GB VRAM) + M.2 SSD + Windows 10 64Bit DCS Panavia Tornado (IDS) really needs to be a thing! Link to comment Share on other sites More sharing options...
Pikey Posted December 4, 2019 Share Posted December 4, 2019 Minor thing... I did ask strongly for the Navgrid and you did quite promptly deliver. That made me feel great as a customer. Have a super Holiday break this year Heat Blur, you guys are awesome! ___________________________________________________________________________ SIMPLE SCENERY SAVING * SIMPLE GROUP SAVING * SIMPLE STATIC SAVING * Link to comment Share on other sites More sharing options...
EntropySG Posted December 4, 2019 Share Posted December 4, 2019 What Pikey said! Thanks HB !!! [sIGPIC][/sIGPIC] Link to comment Share on other sites More sharing options...
Recommended Posts