Lobinjaevel Posted August 31, 2019 Share Posted August 31, 2019 You've made a lot of progress, really inspiring! Now I want a laser engraver too! :) Link to comment Share on other sites More sharing options...
tekadept Posted September 15, 2019 Author Share Posted September 15, 2019 Whilst still working on finalising the F18 panels, I've got the annoying little ones in. I got somebody requested 2 A10 panels, so I thought this was an interesting distraction. First up I did the Right Lighting Panel Then Followed up with the Yaw / SAS Panel I will eventually do more A10 panels and other fighters as well , but now I must get this F18 Master panel done! "Lead me, follow me, or get the hell out of my way" (Gen. George Patton) https://www.tekcreations.space Link to comment Share on other sites More sharing options...
Lobinjaevel Posted September 15, 2019 Share Posted September 15, 2019 Very high quality finish, great job mate! Link to comment Share on other sites More sharing options...
Deadman Posted September 15, 2019 Share Posted September 15, 2019 just curious where are you getting your designs? https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
Phantom_Mark Posted September 16, 2019 Share Posted September 16, 2019 very cool work Link to comment Share on other sites More sharing options...
avidflyer Posted September 17, 2019 Share Posted September 17, 2019 Link to comment Share on other sites More sharing options...
tekadept Posted September 22, 2019 Author Share Posted September 22, 2019 just curious where are you getting your designs? I am using NATOPS as the base of the designs, and have also extracted DCS texture files to help (they are different scale but help fill some gaps, For a few plates I also have some old PDF's which aren't to scale that I put in the mix as well to help come up with So its a bit of a franken effort for the final result. I got one panel from him and it looks very good. It was shipped very fast. ������������ Glad it arrived nice and quick and you like it! "Lead me, follow me, or get the hell out of my way" (Gen. George Patton) https://www.tekcreations.space Link to comment Share on other sites More sharing options...
Deadman Posted September 22, 2019 Share Posted September 22, 2019 ok thanks https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
tekadept Posted October 5, 2019 Author Share Posted October 5, 2019 Been going through the last of the Major F18 Panels, First up the Volume Panel The IR Control panel, the SPN is seperate so that way I can mount in the LED, and made it easier to increase the height. Then I figured out what I'm doing with the master Arm Panel, I went through and added some spacing between the AA AG buttons, and made the bottom layer cut out a little bigger, this makes it captive. Then I will look at mounting a small tactile button behind it later to capture the presses. For the Ext Button, I have sourced an Illuminated Rectangle button that I will be using. it will fit in the square hole, but also will allow me if I get around to it later perhaps making a custom button, Not sure yet. The only Major sized panel left is the Hud control panel which I hope to knock off over the weekend, then its all the smaller ones to knock off in between other projects. "Lead me, follow me, or get the hell out of my way" (Gen. George Patton) https://www.tekcreations.space Link to comment Share on other sites More sharing options...
Phantom_Mark Posted December 3, 2019 Share Posted December 3, 2019 Just wanted to endorse this mans work here, I bought several panels to start building a budget solution. His panels look great..I may or may not illuminate them at some point but for what I needed they are spot on, here i a pic mounted on a test piece....the MDF is a placeholder until I find an alternative plastic, the one I planned to use kept cracking when trying to drill it. Link to comment Share on other sites More sharing options...
BlacleyCole Posted December 6, 2019 Share Posted December 6, 2019 Are these complete plug in\mplay panels or are they just the faceplates BlackeyCole 20years usaf XP-11. Dcs 2.5OB Acer predator laptop/ i7 7720, 2.4ghz, 32 gb ddr4 ram, 500gb ssd,1tb hdd,nvidia 1080 8gb vram New FlightSim Blog at https://blackeysblog.wordpress.com. Go visit it and leave me feedback and or comments so I can make it better. A new post every Friday. Link to comment Share on other sites More sharing options...
tekadept Posted December 6, 2019 Author Share Posted December 6, 2019 Looks good Phantom_Mark Are these complete plug in\mplay panels or are they just the faceplates I do Plates seperate which is what these are, but I also do Plug and Play control boxes. Currently available F18 Replica Right Panel https://www.tekcreations.space/product/f18-hornet-replica-right-control-panel/ F18 Multi Combined Panel https://www.tekcreations.space/product/f18-hornet-control-panel/ I'm currently working on an F16 right at the moment which should hopefully be finished soon. Cheers Tekadept "Lead me, follow me, or get the hell out of my way" (Gen. George Patton) https://www.tekcreations.space Link to comment Share on other sites More sharing options...
tekadept Posted April 29, 2020 Author Share Posted April 29, 2020 I have been Finishing off the F18 Panels, the latest ones added to the list.. Also worked on a IFEI panel, this uses clear acrylic for the middle to repesent the LCD/glass, and can have a paper insert for the instruments for visual appeal. Also cut out some guages frames as well "Lead me, follow me, or get the hell out of my way" (Gen. George Patton) https://www.tekcreations.space Link to comment Share on other sites More sharing options...
Recommended Posts