macedk Posted September 26, 2020 Share Posted September 26, 2020 Hi all :) So like so many others, I loaded my harms and had a sam site at WP1. Had Wagner's video up, to back me up. Harm page is on and all is powered up. Flying to waypoint one, getting close.... Nothing on the harm page ??? Now over the waypoint and raw goes off with a tracking sound and 4 seconds later dead ?? Hmm what went wrong here...hmm thinking... The genius that I am, I loaded a sa-13 which is electrical optical tracking system. Haven't tested the harm since....tough pill to swallow ;) Thank god it is just a simulation hahaha :) OS: Win10 home 64bit*MB: Asus Strix Z270F/ CPU: Intel I7 7700k /Ram:32gb_ddr4 GFX: Nvidia Asus 1080 8Gb Mon: Asus vg2448qe 24" Disk: SSD Stick: TM Warthog #1400/Saitek pro pedals/TIR5/TM MFDs [sIGPIC][/sIGPIC] Link to comment Share on other sites More sharing options...
Eaglewings Posted September 27, 2020 Share Posted September 27, 2020 Did you select the threat table that matches the sa-13 detection profile? Windows 10 Pro 64bit|Ryzen 5600 @3.8Ghz|EVGA RTX 3070 XC3 Ultra|Corair vengence 32G DDR4 @3200mhz|MSI B550|Thrustmaster Flightstick| Virpil CM3 Throttle| Thrustmaster TFRP Rudder Pedal /Samsung Odyssey Plus Headset Link to comment Share on other sites More sharing options...
ED Team BIGNEWY Posted September 27, 2020 ED Team Share Posted September 27, 2020 Hi SAM probably started in a green alert status, try with them set to RED alert status. :) Forum rules - DCS Crashing? Try this first - Cleanup and Repair - Discord BIGNEWY#8703 - Youtube - Patch Status Windows 11, NVIDIA MSI RTX 3090, Intel® i9-10900K 3.70GHz, 5.30GHz Turbo, Corsair Hydro Series H150i Pro, 64GB DDR @3200, ASUS ROG Strix Z490-F Gaming, HP Reverb G2 Link to comment Share on other sites More sharing options...
macedk Posted September 27, 2020 Author Share Posted September 27, 2020 Hi SAM probably started in a green alert status, try with them set to RED alert status. :) Thanks :) Yeah I started like 50 nm from it. I'll go try that :) OS: Win10 home 64bit*MB: Asus Strix Z270F/ CPU: Intel I7 7700k /Ram:32gb_ddr4 GFX: Nvidia Asus 1080 8Gb Mon: Asus vg2448qe 24" Disk: SSD Stick: TM Warthog #1400/Saitek pro pedals/TIR5/TM MFDs [sIGPIC][/sIGPIC] Link to comment Share on other sites More sharing options...
macedk Posted September 29, 2020 Author Share Posted September 29, 2020 I place a single sa-13 in red state and fly over after 4 minutes. Sa-13 engages at roughly 2 nm before i overfly it. I don't get any indication on the harm display. I will try sending an ai into the threat zone and see if it shows up on my harm display. OS: Win10 home 64bit*MB: Asus Strix Z270F/ CPU: Intel I7 7700k /Ram:32gb_ddr4 GFX: Nvidia Asus 1080 8Gb Mon: Asus vg2448qe 24" Disk: SSD Stick: TM Warthog #1400/Saitek pro pedals/TIR5/TM MFDs [sIGPIC][/sIGPIC] Link to comment Share on other sites More sharing options...
Tholozor Posted September 29, 2020 Share Posted September 29, 2020 The radar on the SA-13 is to provide range-only data to the operator, the launcher itself is aimed manually. It's possible to get a HARM off on it, but the launcher isn't likely to use its radar until you're close enough for it to spot you visually. REAPER 51 | Tholozor VFA-136 (c.2007): https://www.digitalcombatsimulator.com/en/files/3305981/ Arleigh Burke Destroyer Pack (2020): https://www.digitalcombatsimulator.com/en/files/3313752/ Link to comment Share on other sites More sharing options...
macedk Posted September 30, 2020 Author Share Posted September 30, 2020 The radar on the SA-13 is to provide range-only data to the operator, the launcher itself is aimed manually. It's possible to get a HARM off on it, but the launcher isn't likely to use its radar until you're close enough for it to spot you visually. ok :) Thanks :) OS: Win10 home 64bit*MB: Asus Strix Z270F/ CPU: Intel I7 7700k /Ram:32gb_ddr4 GFX: Nvidia Asus 1080 8Gb Mon: Asus vg2448qe 24" Disk: SSD Stick: TM Warthog #1400/Saitek pro pedals/TIR5/TM MFDs [sIGPIC][/sIGPIC] Link to comment Share on other sites More sharing options...
Recommended Posts