Deadman Posted July 13, 2012 Share Posted July 13, 2012 (edited) Here is a list of knobs available for the left console. Prices are listed with each panel Transparent cast knobs will have clear after them they can be painted then back lit.The knobs are still curing I will run a Paint test in the next day or two. Any knob or part with N/A behind it is Not yet available. Fuel Systems Control Panel Knobs from left to right Name Material Quantity Exterior Lighting Dial. Clear $ 6.00 Fill Disable Wing/ Main set of 4 Black $ 3.00 ea $12.00 RCVR Knob Solid Gray $10.00 Total $ 28.00 Aux Light Panel Name Material Quantity Refueling / Indexer Lights Dial Clear 1 $ 6.00 Weapon Station Dimmer Dial Clear 1 $ 6.00 Total $ 12.00 SAS Panel Name Material Quantity Yaw Trim Control Knob Clear 1 $ 6.00 Total $ 6.00 Intercom Name Material Quantity HM, INT, AIM, FM,IFF, VHF, ILS, UHF,TCN $ Black 9 Volume Black 1 Rotary Selector knob knob is Black 1 Dial with out engraving plate is clear Total $ 52.00 Sold as a set Stall warning Panel Name Material Quantity Stall 1 $ 6.00 Peak 1 $ 6.00 Total $ 12.00 AN/ARC 186 Am/ FM Panel Sold only as a complete set in Gray or Black Name Material Quantity Preset Channel Selector Wheel. Gray 1 the numbered ring is N/A at this time i need to find some one that can make them. Frequency Selector Knobs. Gray or Black 4 Volume Knob. Gray or Black 1 Frequency Mode Dial. Gray or Black 1 Frequency Selection Dial Gray or Black 1 Total $ 52.00 per set, sold as a set AN/ARC 164 All knobs are solid gray Knobs listed from left to right top to bottom Zero Min Sq 1 Preset Channel Selector. 1 Frequency Selector 5 Main Dial. 1 Volume Knob. 1 Preset Dial. 1 The Volume knob is at the bottom next to its copy I am trying very hard to match the shade of gray but you may wish to paint these as well to match your other knobs Total $ 60.00 per set, sold as a set KY 58 Mode Dial.Clear 1 Plain Dial. Clear 1 Fill. Black 1 Total $ 18.00 For a complete Left side of knobs it will be $292.00 not including PayPal fees if you wish to pay that way,and shipping cost. Edited February 8, 2015 by Deadman https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
Deadman Posted July 14, 2012 Author Share Posted July 14, 2012 Post updated with prices https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
avlolga Posted July 15, 2012 Share Posted July 15, 2012 Hi DM, Many Thanks for your time and great work. you have my address with you, let me know the shipping cost for this package (full left console knob) i will send you payment. Again Many Thanks !!! Avi Link to comment Share on other sites More sharing options...
Deadman Posted July 15, 2012 Author Share Posted July 15, 2012 Hey thanks The response has been great on these. I will check on shipping options this week for international orders. I will be posting the right consel soon so international members may wish to wait a few days befor ordering. Please remember all of the knobs sold have no holes the solid non back lit are cast in black or gray resin and the back lightable knobs are clear with out any holes. there is an great tutorial on Viperpits on drilling holes in knobs http://www.viperpits.org/smf/index.php?topic=6776.0 https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
moken Posted July 17, 2012 Share Posted July 17, 2012 Hi Deadman, may I order from you? You knew my address is Hong Kong Link to comment Share on other sites More sharing options...
Deadman Posted July 17, 2012 Author Share Posted July 17, 2012 (edited) HI guys I have checked on shipping the left console fits with some room to spare.International shipping cost are in a USPS Priority Mail flat rate box. 18.25 + 11.75 registered mail to track the boxes for a total of $30.00. States side is $7.00 with delivery conformation Edited July 18, 2012 by Deadman https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
Cowboy10uk Posted July 18, 2012 Share Posted July 18, 2012 Hi Deadman, Another stunning sale from you. I'm impressed. Quick question are these items going to be limited, or will it be possible to order them at a later date. Would love to order a full set, but just spent all my money on a new pc, so I will need to hold off for a few months to get the money together. Keep up the stunning wok for this community, you are a god send. Cowboy10uk [sIGPIC][/sIGPIC] Fighter pilots make movies, Attack pilots make history, Helicopter pilots make heros. :pilotfly: Corsair 570x Crystal Case, Intel 8700K O/clocked to 4.8ghz, 32GB Vengeance RGB Pro DDR4 3200 MHZ Ram, 2 x 1TB M2 drives, 2 x 4TB Hard Drives, Nvidia EVGA GTX 1080ti FTW, Maximus x Hero MB, H150i Cooler, 6 x Corsair LL120 RGB Fans And a bloody awful Pilot :doh: Link to comment Share on other sites More sharing options...
avlolga Posted July 18, 2012 Share Posted July 18, 2012 HI guys I have checked on shipping the left console fits with some room to spare in a USPS Priority Mail flat rate box. 18.25 + 11.75 registered mail to track the boxes for a total of $30.00. States side is $7.00 with delivery conformation Hi DM, i will like to order 2X "Knobs Left Console" , if it's possible i like it to be shipped together but in 2 separated box's. i have another friend like your great work. i will send you payment for them booth next week. Thanks again. Avi Link to comment Share on other sites More sharing options...
Deadman Posted July 18, 2012 Author Share Posted July 18, 2012 (edited) HI demand is limited with these items, as is the time I can work on these. As for still producing these knobs in several months i have no idea. Thanks Hi Deadman, Another stunning sale from you. I'm impressed. Quick question are these items going to be limited, or will it be possible to order them at a later date. Would love to order a full set, but just spent all my money on a new pc, so I will need to hold off for a few months to get the money together. Keep up the stunning wok for this community, you are a god send. Cowboy10uk Edited July 18, 2012 by Deadman https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
Kenan Posted July 18, 2012 Share Posted July 18, 2012 ^^How difficult is it to plug those in? Via USB or some additional "manual" work is required? Thanks. [sIGPIC][/sIGPIC] Commanding Officer of: 2nd Company 1st financial guard battalion "Mrcine" See our squads here and our . Croatian radio chat for DCS World Link to comment Share on other sites More sharing options...
Deadman Posted July 18, 2012 Author Share Posted July 18, 2012 Kenan I am not sure what you asking about all I am selling are copies of knobs. If you asking about connecting switches ,rotaries or indicator lamps to an interface card there are other threads about that. ^^How difficult is it to plug those in? Via USB or some additional "manual" work is required? Thanks. https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
moken Posted July 18, 2012 Share Posted July 18, 2012 Hi DM, Thank you so much for your development , your knoks is really so beautifull , You are the best Link to comment Share on other sites More sharing options...
Cowboy10uk Posted July 18, 2012 Share Posted July 18, 2012 HI demand is limited with these items, as is the time I can work on these. As for still producing these knobs in several months i have no idea. Thanks Ok mate no probs. think I'll have to miss out this time, but will keep an eye on your sales, no point building a cockpit without a pc to run it ;) Thanks again for doing these items for the community, really appreciated, and thanks for your quick answer. Cowboy10uk [sIGPIC][/sIGPIC] Fighter pilots make movies, Attack pilots make history, Helicopter pilots make heros. :pilotfly: Corsair 570x Crystal Case, Intel 8700K O/clocked to 4.8ghz, 32GB Vengeance RGB Pro DDR4 3200 MHZ Ram, 2 x 1TB M2 drives, 2 x 4TB Hard Drives, Nvidia EVGA GTX 1080ti FTW, Maximus x Hero MB, H150i Cooler, 6 x Corsair LL120 RGB Fans And a bloody awful Pilot :doh: Link to comment Share on other sites More sharing options...
Deadman Posted July 18, 2012 Author Share Posted July 18, 2012 No problem get a hold of me when you have the money and we will see if i am still making these. https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
Deadman Posted July 19, 2012 Author Share Posted July 19, 2012 HI Guys please make sure you name and postal address and what you order is in the comment section of your Pay pal payment. All so this is not a big sale or any thing I am offering the knobs for a limited time I don't have the space and the wife will only put up with the smell and mess for so long. If you want knobs you really should make your orders and Payments now. I have possibly found both knobs for the AAP panel https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
moken Posted July 22, 2012 Share Posted July 22, 2012 Hi DM, Otherwise, Left console including have IFF, could you develop IFF's knob further for us? Link to comment Share on other sites More sharing options...
Deadman Posted July 22, 2012 Author Share Posted July 22, 2012 HI moken with the availability of purchasing a complete IFF units on eBay there is no reason for me to make the knobs. I have posted before there is just no demand for those knobs thanks Hi DM, Otherwise, Left console including have IFF, could you develop IFF's knob further for us? https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
moken Posted July 23, 2012 Share Posted July 23, 2012 Thanks DM, since I have no real IFF, so I need IFF's knobs. Link to comment Share on other sites More sharing options...
Deadman Posted July 23, 2012 Author Share Posted July 23, 2012 (edited) Hum no idea what to say after three times Edited July 23, 2012 by Deadman https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
moken Posted July 23, 2012 Share Posted July 23, 2012 (edited) Hi DM, sorry, now i understand, Thank you Edited July 23, 2012 by moken Link to comment Share on other sites More sharing options...
Deadman Posted July 30, 2012 Author Share Posted July 30, 2012 First shipments will be mail tomorrow pms have been sent https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
Deadman Posted July 30, 2012 Author Share Posted July 30, 2012 Here is the RCVR Knob bottom lay out with depth for the slot for the aluminum arm https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
JCook Posted August 3, 2012 Share Posted August 3, 2012 Deadman - I just recieved the left console knobs in the mail today. Excellent quality and very good packaging. Thanks! Link to comment Share on other sites More sharing options...
Deadman Posted August 3, 2012 Author Share Posted August 3, 2012 That is great news I can't wait to see them on your panels :thumbup: https://www.shapeways.com/shops/a-10c-warthog-supplies https://forum.dcs.world/topic/133818-deadmans-cockpit-base-plans/#comment-133824 CNCs and Laser engravers are great but they can't do squat with out a precise set of plans. Link to comment Share on other sites More sharing options...
Dropship Pilot Posted August 17, 2012 Share Posted August 17, 2012 Just got the parts in. Top quality - those casts look like injection molded! Can't wait to get the next batch. Cheers, Stefan Link to comment Share on other sites More sharing options...
Recommended Posts