Swine Posted November 15, 2018 Share Posted November 15, 2018 Ok. I have my Virpil software working now. It is showing PCB version 3 and the buttons are working fine in DCS. DCS seems to identify my stick in the mapping section(X and Y). However when I run DCS the roll and pitch do not work. The buttons on the stick work fine but for some reason I can’t get the roll and pitch to work. I have to be doing something wrong in the programming in DCS. Any suggestions? Thanks Also, the pitch and roll worked fine without the software when I initially plugged the stick in and ran DCS. Link to comment Share on other sites More sharing options...
Ala12Rv-Tundra Posted November 15, 2018 Share Posted November 15, 2018 do both axis work using the VPC COnfiguration tool? does the graphic changes when you move the joy, under the "VPC Joy tester"? i5 8400 | 32 Gb RAM | RTX 2080Ti | Virpil Mongoose T-50 base w/ Warthog & Hornet sticks | Warthog throttle | Cougar throttle USB | DIY Collective | Virpil desk mount | VKB T-Rudder Mk IV | Oculus Rift S | Buddy-Fox A-10 UFC | 3x TM MFDs | 2x bass shakers pedal plate| SIMple SIMpit chair | WinWing TakeOff panel | PointCTRL v2 | Andre JetSeat | Winwing Hornet UFC | Winwing Viper ICP FC3 - Warthog - F-5E - Harrier - NTTR - Hornet - Tomcat - Huey - Viper - C-101 - PG - Hip - SuperCarrier - Syria - Warthog II - Hind - South Atlantic - Sinai - Strike Eagle Link to comment Share on other sites More sharing options...
Swine Posted November 16, 2018 Author Share Posted November 16, 2018 Yes it does work in the vpc configuration tool. Link to comment Share on other sites More sharing options...
dburne Posted November 16, 2018 Share Posted November 16, 2018 Check for duplicate axis assignments. Don B EVGA Z390 Dark MB | i9 9900k CPU @ 5.1 GHz | Gigabyte 4090 OC | 64 GB Corsair Vengeance 3200 MHz CL16 | Corsair H150i Pro Cooler |Virpil CM3 Stick w/ Alpha Prime Grip 200mm ext| Virpil CM3 Throttle | VPC Rotor TCS Base w/ Alpha-L Grip| Point Control V2|Varjo Aero| Link to comment Share on other sites More sharing options...
SVgamer72 Posted November 16, 2018 Share Posted November 16, 2018 Are any of the axes lines in DCS for the module(s) settings red? Link to comment Share on other sites More sharing options...
Swine Posted November 16, 2018 Author Share Posted November 16, 2018 I will check that and I will also make sure there are no other assignments to the x and y axis in the DCS key mapping. I don’t think there are but will double check. Thx guys Link to comment Share on other sites More sharing options...
Swine Posted November 16, 2018 Author Share Posted November 16, 2018 Link to comment Share on other sites More sharing options...
Swine Posted November 16, 2018 Author Share Posted November 16, 2018 All fixed now. I had a conflict with another device. I knew it had to be an easy fix. Link to comment Share on other sites More sharing options...
dburne Posted November 16, 2018 Share Posted November 16, 2018 All fixed now. I had a conflict with another device. I knew it had to be an easy fix. :thumbup: Have fun! Don B EVGA Z390 Dark MB | i9 9900k CPU @ 5.1 GHz | Gigabyte 4090 OC | 64 GB Corsair Vengeance 3200 MHz CL16 | Corsair H150i Pro Cooler |Virpil CM3 Stick w/ Alpha Prime Grip 200mm ext| Virpil CM3 Throttle | VPC Rotor TCS Base w/ Alpha-L Grip| Point Control V2|Varjo Aero| Link to comment Share on other sites More sharing options...
Bob_Bushman Posted November 16, 2018 Share Posted November 16, 2018 Yeah DCS grabs all possible devices and bind them to pitch, roll and yaw as soon as it finds them. So if you plugin a new throttle or something it's immediately bound to pitch, roll and yaw etc etc. i7 8700k @ 4.7, 32GB 2900Mhz, 1080ti, CV1 Virpil MT-50\Delta, MFG Crosswind, Warthog Throttle, Virptil Mongoost-50 throttle. Link to comment Share on other sites More sharing options...
Recommended Posts