Jump to content

Introducing the VPC MongoosT-50


Cyph3r

Recommended Posts

Anyone swapped the cams yet.

 

I have my Roll cam swapped but the Pitch Cam will not come out and I have tried pretty forcefully worried about breaking the whole dam thing.

 

Ok its a pain in the Arse but to do it take a small torx put it in the screw hole be careful not to get into the threads of the mount and then lever the thing out against the Cam Gymbal mount.

 

Also watch the logic board it has spacer washer and nut between it and the side to stop it getting bent when you tighten it. took me 2 hours to work through it all still it works.

 

Cheers

 

Windy

 

It definitely isn't an easy process, but I was able to work it loose with side-to-side motion with my fingers, although I had a flathead screwdriver on standby.

 

i9 12900k @ 4.9ghz, 32gb RAM

Nvidia RTX 3090

Windows 11 x64

Valve Index

Brunner CLS-E w/RS F16GRH, Virpil TCS Rotor Plus Collective, BRD F1 Pedals, WH Throttle, FSSB R3 w/WH Grip, PointCTRL v1

Link to comment
Share on other sites

  • Replies 2.3k
  • Created
  • Last Reply

Top Posters In This Topic

Yea I got it all done I am using the soft center 3 dot Cams and the medium springs. I have a 30 cm extension on it and it centers great with the Virpil stick top.

 

After couple of hours using it I am very happy it took me a couple of hours to sort through the Cam swap but it is all set up now.

 

The sensors are excellent I see the in game stick reflect every tiny movement ( way better than my 5 year old Warthog ). There is zero sticktion and formation flying is a joy.

 

I have recommended they send them out with the soft center cam to save the Cam change Pain which I think the majority of us would prefer, tho it would be interesting to hear from someone with a Warthog stick top on it as the extra weight does make a difference.

 

 

 

Sent from my SM-G955U using Tapatalk

I7 3930 4.2GHz ( Hyperthreading Off), GTX1080, 16 GB ddr3

Hotas Warthog Saiteck Combat Pedals HTC Vive, Oculus CV1.

 

GTX 1080 Has its uses

Link to comment
Share on other sites

 

I have recommended they send them out with the soft center cam to save the Cam change Pain which I think the majority of us would prefer, tho it would be interesting to hear from someone with a Warthog stick top on it as the extra weight does make a difference.

 

 

 

Sent from my SM-G955U using Tapatalk

 

 

Mine will be sent at the beginning of next week I hope. When i get my hands on it I will sure be sure to let you guys know. I might switch to no center and medium springs on warthog with 12 cm extension because I fly helo's mostly.


Edited by kingpinda
Link to comment
Share on other sites

I did try the the hard Cam 1st but for formation I would have had to fly out of trim to stay out of the center notch.

 

Then I took it apart

 

Sent from my SM-G955U using Tapatalk

I7 3930 4.2GHz ( Hyperthreading Off), GTX1080, 16 GB ddr3

Hotas Warthog Saiteck Combat Pedals HTC Vive, Oculus CV1.

 

GTX 1080 Has its uses

Link to comment
Share on other sites

Yea I got it all done I am using the soft center 3 dot Cams and the medium springs. I have a 30 cm extension on it and it centers great with the Virpil stick top.

 

After couple of hours using it I am very happy it took me a couple of hours to sort through the Cam swap but it is all set up now.

 

The sensors are excellent I see the in game stick reflect every tiny movement ( way better than my 5 year old Warthog ). There is zero sticktion and formation flying is a joy.

 

I have recommended they send them out with the soft center cam to save the Cam change Pain which I think the majority of us would prefer, tho it would be interesting to hear from someone with a Warthog stick top on it as the extra weight does make a difference.

 

 

 

Sent from my SM-G955U using Tapatalk

 

Thanks for posting your experience with changing over the cams.

 

It would be nice to be able to state your preferred cam/spring combination when ordering the stick.

 

I would like to receive my Mongoos T-50 flight stick with the soft centre cams already installed to save the hassle of changing them over.

 

As I have yet to receive a shipping notice I have put in this request. Hopefully they will be able to accommodate me...

Link to comment
Share on other sites

Yea I got it all done I am using the soft center 3 dot Cams and the medium springs. I have a 30 cm extension on it and it centers great with the Virpil stick top.

 

After couple of hours using it I am very happy it took me a couple of hours to sort through the Cam swap but it is all set up now.

 

The sensors are excellent I see the in game stick reflect every tiny movement ( way better than my 5 year old Warthog ). There is zero sticktion and formation flying is a joy.

 

I have recommended they send them out with the soft center cam to save the Cam change Pain which I think the majority of us would prefer, tho it would be interesting to hear from someone with a Warthog stick top on it as the extra weight does make a difference.

 

 

 

Sent from my SM-G955U using Tapatalk

 

:thumbsup:

 

I'm glad to hear the time spent changing the cam was worth it and that you're enjoying the MT-50!

 

Based on these comments, we'll be shipping out future orders of the MT-50 with the soft-center cams installed as standard!

► Website: www.virpil.com // ► Facebook: https://www.facebook.com/VirPilControls // ► Twitter: https://twitter.com/VirPilControls

For support please email support@virpil.com to open a ticket!

 

[sIGPIC][/sIGPIC]

Link to comment
Share on other sites

Hi

 

@Cyph3r:

Can you please post the measurements for the U-Bracket on the T50 Base. So i can make an adapter to mount the Base on my Deskmount.

 

Thanks

 

Here's the dimensions of the U-Bracket. Of course you could replace the U-Bracket entirely and mount to where the U-Bracket mounts to.

 

VPC_MT-50_UBRACKET_02.jpg

 

 

The u bracket makes mounting fairly complicated... no way to mount this from the bottom of the base using 4 screws?

 

You could. But we definitely wouldn't recommend it!

► Website: www.virpil.com // ► Facebook: https://www.facebook.com/VirPilControls // ► Twitter: https://twitter.com/VirPilControls

For support please email support@virpil.com to open a ticket!

 

[sIGPIC][/sIGPIC]

Link to comment
Share on other sites

Does it have Z axis ?

Thank you

I9 12900k@ 5 GHz | 32 GB DDR4 | Asus ROG  Strix Z690-A Gaming Wifi d4| RTX 3090 | 6 TB SSD + 8 TB HDD | 4K Samsung Q90R 55" | VKB MK III PRO L | Virpil Throttle MONGOOST-50 | MFG Crosswind | TrackIR5

Link to comment
Share on other sites

Here's the dimensions of the U-Bracket. Of course you could replace the U-Bracket entirely and mount to where the U-Bracket mounts to.

That sounds good to me!

Can you provide a drawing that would help to prepare that solution?

I have the Monstertech table mounts and want to continue using those.

LeCuvier

Windows 10 Pro 64Bit | i7-4790 CPU |16 GB RAM|SSD System Disk|SSD Gaming Disk| MSI GTX-1080 Gaming 8 GB| Acer XB270HU | TM Warthog HOTAS | VKB Gladiator Pro | MongoosT-50 | MFG Crosswind Pedals | TrackIR 5

Link to comment
Share on other sites

That sounds good to me!

Can you provide a drawing that would help to prepare that solution?

I have the Monstertech table mounts and want to continue using those.

 

If you look on the diagram I posted of the U-Bracket, the narrower section with the 4 screw holes is the dimensions to mount to the rear side of the base (thus replacing the U-bracket) :thumbup:

► Website: www.virpil.com // ► Facebook: https://www.facebook.com/VirPilControls // ► Twitter: https://twitter.com/VirPilControls

For support please email support@virpil.com to open a ticket!

 

[sIGPIC][/sIGPIC]

Link to comment
Share on other sites

That sounds good to me!

Can you provide a drawing that would help to prepare that solution?

I have the Monstertech table mounts and want to continue using those.

 

Not sure of the timing, but MonsterTech will be offering a plate for their table mounts to accommodate the Mongoose base. I had asked them about this earlier.

Don B

EVGA Z390 Dark MB | i9 9900k CPU @ 5.1 GHz | Gigabyte 4090 OC | 64 GB Corsair Vengeance 3200 MHz CL16 | Corsair H150i Pro Cooler |Virpil CM3 Stick w/ Alpha Prime Grip 200mm ext| Virpil CM3 Throttle | VPC Rotor TCS Base w/ Alpha-L Grip| Point Control V2|Varjo Aero|

Link to comment
Share on other sites

Not sure of the timing, but MonsterTech will be offering a plate for their table mounts to accommodate the Mongoose base. I had asked them about this earlier.

Yes I know, but they need to have a T-50 before they will finalize design and make it (so they told me)

LeCuvier

Windows 10 Pro 64Bit | i7-4790 CPU |16 GB RAM|SSD System Disk|SSD Gaming Disk| MSI GTX-1080 Gaming 8 GB| Acer XB270HU | TM Warthog HOTAS | VKB Gladiator Pro | MongoosT-50 | MFG Crosswind Pedals | TrackIR 5

Link to comment
Share on other sites

Hi Cyph3r, when I try to change the spring I find that one of the spring loading screw(roll axis) is off center and the white plastic is rubbing the inner side of the tube. This makes it hard to adjust from through the hole in the top plate and increases the friction. Is there a fix to that?

Link to comment
Share on other sites

Yes I know, but they need to have a T-50 before they will finalize design and make it (so they told me)

 

Yeah, they told me they had one on pre-order, so maybe won't be too much longer now.

Don B

EVGA Z390 Dark MB | i9 9900k CPU @ 5.1 GHz | Gigabyte 4090 OC | 64 GB Corsair Vengeance 3200 MHz CL16 | Corsair H150i Pro Cooler |Virpil CM3 Stick w/ Alpha Prime Grip 200mm ext| Virpil CM3 Throttle | VPC Rotor TCS Base w/ Alpha-L Grip| Point Control V2|Varjo Aero|

Link to comment
Share on other sites

I think I have come to conclusion that all the extra cams I got are deflective.

Since I am only able to remove the roll cam. I replaced the hard one with the soft one and found that the movement is not smooth when I move the stick to the right edge. After I inspected the cam I thought it's because of the surface of the cam so I reverse the cam and the left edge of the stick is not smooth now...

 

And then I compare those cam with the hard cam I found that the contacting surface of the hard cams had been smoothed and it's color is silvery metal color while all the other cams are with black coating.

 

edit: add photos

 

http://imgur.com/tuZ5xCR

 

http://imgur.com/3a52Unv

 

And here is the whole t50 album

 

http://imgur.com/a/tNZdz


Edited by insanedruid
Link to comment
Share on other sites

I think I have come to conclusion that all the extra cams I got are deflective.

Since I am only able to remove the roll cam. I replaced the hard one with the soft one and found that the movement is not smooth when I move the stick to the right edge. After I inspected the cam I thought it's because of the surface of the cam so I reverse the cam and the left edge of the stick is not smooth now...

 

And then I compare those cam with the hard cam I found that the contacting surface of the hard cams had been smoothed and it's color is silvery metal color while all the other cams are with black coating.

 

edit: add photos

 

http://imgur.com/tuZ5xCR

 

http://imgur.com/3a52Unv

 

And here is the whole t50 album

 

http://imgur.com/a/tNZdz

 

Hi Insanedruid!

 

Ah, I'm sorry yours have arrived not perfectly smooth, can I propose (for the time being) you polish the surface with something like 800-1200 grit wet and dry, and we'll ship another set of cams out to you ASAP!

 

Please email sale@virpil.com referencing this with your order number and we'll sort it out immediately!

 

We'll also look into why these cams were not up to the standard they should have been and I urge anyone who has a similar sort of issue with their cams to email me at sale@virpil.com!


Edited by Cyph3r

► Website: www.virpil.com // ► Facebook: https://www.facebook.com/VirPilControls // ► Twitter: https://twitter.com/VirPilControls

For support please email support@virpil.com to open a ticket!

 

[sIGPIC][/sIGPIC]

Link to comment
Share on other sites

Anyone swapped the cams yet.

 

I have my Roll cam swapped but the Pitch Cam will not come out and I have tried pretty forcefully worried about breaking the whole dam thing.

 

Ok its a pain in the Arse but to do it take a small torx put it in the screw hole be careful not to get into the threads of the mount and then lever the thing out against the Cam Gymbal mount.

 

Also watch the logic board it has spacer washer and nut between it and the side to stop it getting bent when you tighten it. took me 2 hours to work through it all still it works.

 

Cheers

 

Windy

 

I got mine last night and was unable to remove the pitch cam... I guess I will have to try it again tonight.

Link to comment
Share on other sites

At your own risk be careful not to get into the threads. Another poster rocked it from side to side to get it loose but mine would not, move this was my last resort.

 

Also when you put the new one into position make sure it is nicely lined up so you dont cross thread the small screws putting them in.

 

Hope this is helpful.2e1f254e9e2c55245f034a3a3891c9b5.jpg

 

Sent from my SM-G955U using Tapatalk


Edited by WindyTX

I7 3930 4.2GHz ( Hyperthreading Off), GTX1080, 16 GB ddr3

Hotas Warthog Saiteck Combat Pedals HTC Vive, Oculus CV1.

 

GTX 1080 Has its uses

Link to comment
Share on other sites

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...