kafete Posted March 21, 2018 Share Posted March 21, 2018 Hello again guys, I have another doubt about the stabilator indicator. Because if you are looking to the EDP the value of the stab indicator some times is different to the MPCD engine page STAB POS indicator. I have just upload another video to show you. Kind regards. https://youtu.be/zFO9kcLjPlI Link to comment Share on other sites More sharing options...
Eldur Posted March 21, 2018 Share Posted March 21, 2018 Maybe the MCPD has a floor() while the EDP uses round() Anyway, the MCPD should show the tenth decimal, like 1.2°. Check 2-20 in the AV-8B-000 NATOPS, pdf page 98. I don't know how this is in case of the EDP. I guess the output there should work like the thrust gauges in the F-15C or the little gauge inside the RPM gauge of the Mirage, so 1.5° would show the upper half of "1" and the lower half of "2". https://imgur.com/a/TawlN <- check the H20 gauge... looks like it its slightly below 500, like 426-427ish. The last 0 is static AFAIK. Link to comment Share on other sites More sharing options...
kafete Posted March 22, 2018 Author Share Posted March 22, 2018 (edited) IN ACCORDANCE WITH THE NATOPS nfm000 2.14.1.2.3 Stabilator Position Indicator Stabilator position is provided on both the EDP and the DDI. The EDP is located on the right side of the main instrument panel and the DDI on the left side (Day Attack aircraft) or either side of the main instrument panel for Radar and Night Attack aircraft. Both indicators display stabilator position in degrees with an arrow to indicate nose up or nose down. Stabilator position on the DDI is displayed on the engine data display and is accessible through the menu display by selecting ENG. But as I read both indicators have to put the same number at the same time (or it is where I thought) Because as in the paragraf above says, both have the same the "same indicator font", so you can read the sabilator position in both indicators So they have to put another digit in the Stab pos in the ENG page in the DDI to show as you said avobe. Edited March 22, 2018 by kafete Link to comment Share on other sites More sharing options...
kafete Posted April 11, 2018 Author Share Posted April 11, 2018 Remind in next update add the second digit to the Stab indicator in the MPCD, at Engine page. Link to comment Share on other sites More sharing options...
kafete Posted April 25, 2018 Author Share Posted April 25, 2018 I have just realize that Razbam didn't update the STAB Position indicator in this Update, could be because it was not clear, I will put a Pic of the correct digits of the STAB POS Indicator (2 digits istead of 1) https://ibb.co/jmHOmx Link to comment Share on other sites More sharing options...
Shrike88 Posted April 26, 2018 Share Posted April 26, 2018 +1 Thanks for pointing this out Link to comment Share on other sites More sharing options...
kafete Posted May 12, 2018 Author Share Posted May 12, 2018 (edited) Zeus67, - CptSmiley Still the same without fix it.... any update about this? Edited May 12, 2018 by kafete Link to comment Share on other sites More sharing options...
kafete Posted May 23, 2018 Author Share Posted May 23, 2018 (edited) Still without updating the STAB POS Indicator ^^ I will put again the link https://ibb.co/jmHOmx You only have to add de decimal digit to the satb position in the Engine display, for example 1.1 1.2 1.3 as I put in the picture. "Solo hay que añadirle un dígito al Engine Display que tienen que ser 2. Ejemplo 1.1 1.2 1.3" como pone el manual" Sorry for the text in spanish but could be clearer to Zeus67. Edited May 23, 2018 by kafete Link to comment Share on other sites More sharing options...
Recommended Posts