Ala12Rv-Tundra Posted June 2, 2018 Share Posted June 2, 2018 Hi people, I have been trying for a while two ways to start the game with no VR, for mission edition, binding the whole Hornet setup, taking screenshoots, by I can´t figure it out. I use Steam. Adding a direct llink with the parameters --force_disable_VR didn´t work Downloading and using Skatezilla updater to force it neither. Any other options besides unplugging the USB ffrom the headset? i5 8400 | 32 Gb RAM | RTX 2080Ti | Virpil Mongoose T-50 base w/ Warthog & Hornet sticks | Warthog throttle | Cougar throttle USB | DIY Collective | Virpil desk mount | VKB T-Rudder Mk IV | Oculus Rift S | Buddy-Fox A-10 UFC | 3x TM MFDs | 2x bass shakers pedal plate| SIMple SIMpit chair | WinWing TakeOff panel | PointCTRL v2 | Andre JetSeat | Winwing Hornet UFC | Winwing Viper ICP FC3 - Warthog - F-5E - Harrier - NTTR - Hornet - Tomcat - Huey - Viper - C-101 - PG - Hip - SuperCarrier - Syria - Warthog II - Hind - South Atlantic - Sinai - Strike Eagle Link to comment Share on other sites More sharing options...
aceviper Posted June 2, 2018 Share Posted June 2, 2018 Switch the Oculus services to manual. Dcs starts in normal 2d then. Use Oculus debug tool to start services and run Dcs in VR. Link to comment Share on other sites More sharing options...
Ala12Rv-Tundra Posted June 2, 2018 Author Share Posted June 2, 2018 Switch the Oculus services to manual. Dcs starts in normal 2d then. Use Oculus debug tool to start services and run Dcs in VR. Unchecking the "options-VR-Enable virtual reality headset" finally did the trick :lol: i5 8400 | 32 Gb RAM | RTX 2080Ti | Virpil Mongoose T-50 base w/ Warthog & Hornet sticks | Warthog throttle | Cougar throttle USB | DIY Collective | Virpil desk mount | VKB T-Rudder Mk IV | Oculus Rift S | Buddy-Fox A-10 UFC | 3x TM MFDs | 2x bass shakers pedal plate| SIMple SIMpit chair | WinWing TakeOff panel | PointCTRL v2 | Andre JetSeat | Winwing Hornet UFC | Winwing Viper ICP FC3 - Warthog - F-5E - Harrier - NTTR - Hornet - Tomcat - Huey - Viper - C-101 - PG - Hip - SuperCarrier - Syria - Warthog II - Hind - South Atlantic - Sinai - Strike Eagle Link to comment Share on other sites More sharing options...
farmertom Posted June 3, 2018 Share Posted June 3, 2018 (edited) Sorry I did not read that you are using stream... Create a .bat file > DCS_VR_OFF.bat paste this into it... "C:\Program Files\Eagle Dynamics\DCS World\bin\DCS.exe" --force_disable_VR Create another .bat file > DCS_VR_ON.bat paste this into it....." C:\Program Files\Eagle Dynamics\DCS World\bin\DCS.exe" --force_VR If your DCS is in a different directory make the appropriate changes. Right click on the .bat file and open. I have open VR checked in the DCS settings. Good Luck Edited June 3, 2018 by farmertom Link to comment Share on other sites More sharing options...
Fri13 Posted June 3, 2018 Share Posted June 3, 2018 Just make a copy of the shortcut you are using to launch the DCS and put this there in similar way as "Target" "C:\DCS World\bin\DCS.exe" --force_disable_VR And that shortcut makes DCS to start in 3D (non-VR). i7-8700k, 32GB 2666Mhz DDR4, 2x 2080S SLI 8GB, Oculus Rift S. i7-8700k, 16GB 2666Mhz DDR4, 1080Ti 11GB, 27" 4K, 65" HDR 4K. Link to comment Share on other sites More sharing options...
Recommended Posts