nikita_nomad

Definetely,thanks for the link!

I'm not aware.

thanks

Hi guys, maybe bit off topic but I didn't know where else to post this. I've been studying 3d modelling and everything around it and I'm looking to put this knowledge to practice. Does anyone know anyone or a company, that needs a 3d modeller for freelance work or anything like that?

I'm planing on upgrade soon and i5 13600k looks very interesting

Thanks a lot for all the input. That was my guess on gpu usage as well. Athough I didn't expect it to be so dramatic. I went with 30x series gpu only because I knew that cpu is next in the line of upgrades. And yeah I will go for a 1440p res definetely. I tried MT version and it makes no difference in frames, however task manager shows increase in cpu usage from around 50 to 75% now. But it makes no difference in fps or at least not enough for me even to notice. If I run a free flight instant action mission frames are way better and gpu is loaded way more but still at around 50%. So I guess it indicates that cpu is struggling less and hence the improvement.

Yeah, I think I'm settled on 1440 defo, it's better for work also. But I guess Ill have to wait till cpu upgrade for the best experience

Thanks for all the replies guys, appreciate it. A bit off topic question, but still. Does anyone have an idea why my gpu is always only 20-30% utilised? I do have an old cpu atm, i7 4770 and 32gb ram. I feel like its just a waste at the moment, I know cpu is old, but really? Such a little use of gpu...Or if anyone could point me in the right direction on forum please. Cheers!

Hi guys, Looking for advice on new monitor. I'm planning to get a new 27 inch screen but not sure should I go with 1080 or 1440? I have a 3060ti and planing to upgrade to i5 13600kf with 32 ram in the next 6 month. What do you guys think would be more worth it? Thanks in advance.

F5 TACAN lives a life of it's own

I found it and just tried it now. No difference at all. GPU usage on pause is around 60% which makes dcs run ok ish, but as soon as I unpause it it drops to 10-15%..Very strange as I tried other missions with lots of units in them and started another campaign which was fine as well. All the time it's above 50% utilisation.

Yeah it's definitely 3060 running, I have 32 gb ddr3. How do I turn off hyper threading?

So I just started the Black Sea resolve campaign for f5 and I was really enjoyoing it until I started noticing that I have quite low fps specifically when playing it. And so I went on to task manager and saw that whenever campaign is running I get really low gpu utilisation, around 10-15% and so it results in a slideshow in game. I can't figure out why, because dcs in general and any other campaign/mission on f5 or any other air frame runs at 60-90%. Weirdly enough as well, if I'm in a mission and on pause(not active one) I suddendly get higher gpu load, as soon as I unpause it drops again to under 20%... I'm out of ideas on this. Any help would be appreciated. Could it be because of cpu bottleneck? It's usage sits at around 50% as well. And it is an old cpu also. Thanks. p.s. gpu is rtx 3060ti, cpu i7 4770.

Thanks for reply, I'll try that. I do have only a4 installed.. I'll duplicate post on the bug section as well.

Message to creator and to anyone that could advice me on this. So I just started the campaign and I was really enjoyoing it until I started noticing that I have quite low fps specifically when playing it. And so I went on to task manager and saw that whenever campaign is running I get really low gpu utilisation, around 10-15% and so it results in a slideshow in game. I can't figure out why, because dcs in general and any other campaign/mission on f5 or any other air frame runs solid at 60-90% and good fps. Weirdly enough as well, if I'm in a mission and on pause(not active one) I suddendly get normal gpu load, as soon as I unpause it drops again to under 20%... I'm out of ideas on this. Any help would be appreciated. Thanks. p.s. gpu is rtx3060ti