Jump to content


  • Content Count

  • Joined

  • Last visited

Everything posted by Rapti

  1. Displays will come later Gesendet von meinem SM-G988B mit Tapatalk
  2. Almost done Gesendet von meinem SM-G988B mit Tapatalk
  3. Progress Gesendet von meinem SM-G988B mit Tapatalk
  4. In my opinion the hardware recommendations from EA are far from sufficient. I have recently built a new PC. ASUS Maximus XII Hero motherboard Intel I9-10909K MSI RTX3800 NZXT Z73 aio water cooling 64GB RAM 2TB m.2 SSD 850W ASUS ROG Thor power supply This is enough to fly with highest settings in DCS with 50 - 100 FPS. And this in singleplayer well understood. Gesendet von meinem SM-G988B mit Tapatalk
  5. Some New pictures... Gesendet von meinem SM-G988B mit Tapatalk
  6. Openhornet.com There are solidworks files
  7. Hi Hans, When the RS485 network did not work, I first tested the individual components. Therefore I tested the NANO and the MEGA board separately. I noticed that the same circuit and the same code does not work with the MEGA board. When I used a PullUp resistor this board worked. The Post#5 referred to this separate test. i just checked the sketch. There is the end bracket. Probably it got lost when copying here in the forum.
  8. so, the first problem is solved. On the MEGA board I definitely need a PullUp resistor on the Push Button.
  9. you are right with 7V for the Nano. I know the thread from Hans - thanks. But why are the Mega's not able go communicate with DCS BIOS? I thinkna have to solve this Problem first. Any idea?
  10. So 1. mistake... Max487 need 12V supply. But the problems starts earlier. When i try just the boards to communicate with DCS BIOS. Just the Arduino UNO and Arduino Nano can communicate with DCS BIOS. I have two MEGA boards. They dont work. I Can upload the Sketch. But nothing happen when connect to DCS BIOS. Any idea?
  11. Hello everyone, i'm trying a first test to communicate with an Arduino Mega and an Arduino Nano via MAX487 chip. Unfortunately I can't get it there at the moment. I want to control the MasterCausion button and the MasterCaution LED as a test. have built the following circuit: --> see attached picture. I On the Adruino Mega I have uploaded the following sketch: /* Tell DCS-BIOS this is a RS-485 Master. You will need to flash this to a Mega 2560. */ #define DCSBIOS_RS485_MASTER /* Define where the TX_ENABLE signals are connected. You can connect up to three half-duplex
  12. Yes when its finished Gesendet von meinem SM-G988B mit Tapatalk
  13. Progress... Gesendet von meinem SM-G988B mit Tapatalk
  14. Yes it's definitely not connecting. Did you try another USB Port? Gesendet von meinem SM-G930F mit Tapatalk
  15. This is the final design. I have now started to laser and engrave the panels. The material is 3mm acrylic white translucent and then painted black. ... and I know, It's "FLY BY" :megalol:
  16. looks great! how are the parking break lever an the wing fold lever works? What switches do you use for this 2 rotate / pul-push lever? --> thats my design.
  17. https://m.facebook.com/story.php?story_fbid=2753338708278664&id=441639040340
  18. Hello together, I am looking for a manual that explains the different toggle switches. What do the different switch positions (on-off, on-off-on, (on)-off-(on) etc. mean? I always find this difficult to order the right switches. e.g. the dispenser switch in the FA18? It is marked with "OFF-ON-BYPASS". Which switch do I need there? OFF-ON-ON?
  19. Hi Jester, ich habe in der Tat erst mit dem 3D Druck begonnen. Ich benutze Cura. Über Tipps bin ich natürlich immer froh. Das Endprodukt wird allerdings nicht 3D gedruckt sondern aus acryl gelasert und graviert. Das Gehäuse werde ich CNC fräsen. Habe seit Jahren ne Stepcraft 600...
  20. Den habe ich selber konstruiert. Gehört zu einer Button Box die ich am Bauen bin. STL files kann ich dir senden. Musst halt sagen was...
  21. Bin auch dran im Moment. Das soll der Fahrwerkshebel geben. Im Griff hats dann noch ne LED welche auch über DCS-BIOS angesteuert wird. Muss noch ein zweiter Rollenschalter einbauen...
  • Create New...