BATCARLO

When in the mission editor I set a DES TOS for an F-16C flight, this is not reported correctly on the cruise page. The first time you enter as single player the DES TOS is correct, but if you change slot it becomes incorrect, and increases over time. In multiplayer, however, it is always wrong and increases over time. The DES TOS instead must always remain the one set in the mission editor. watch the video

Hi, when I set elevation wp from 150 ft to 161 ft, I get 1 foot less. That is if I set ft 152, I get ft 151; with ft 157, I get ft 156 and so on. Please check this video: FA18C WRONG ALTITUDE.mp4

I have tried again successfully. It is necessary to obscure any reflection sources as any additional screens. (where I had extracted the DDI of the F / A-18C). You can do this test, get up from the chair, to move away from the reflection sorces, and re-center the VR view. Another test you can do is to move away from the desk or turn around 90 or 180 degrees, to move away from the reflection sorces, and re-center the VR view.

Take a look: https://www.dropbox.com/s/i9hxfk7p887hqcq/SA5B55 180 degrees turn-00.mkv?dl=0 and another track https://www.dropbox.com/s/twnv4visuzfawtp/SA5B55 180 degrees turn-01.mkv?dl=0 We play with "map only", so we can't track DCS reply...

I am attaching a screenshot from TacView, where you can see the impossible 180 ° turns of the SA5B55, also made without loss of speed ...

Yes, now it's running, but it's not usefull for me...

for me is the same

In GMT radar, also in SEA radar, do not designate moving target with TDC DEPRESS, but designate with Sensor Control Switch in the direction of the DDI with GMT (or SEA) radar. The radar sensor designate keeps moving target, you see his direction and speed... The maverick sensors, when ungaged, points the right target. Sorry my bad English.

Markpoints cannot be designated. Sorry now its working...

Undesignate also deletes too assignments. See the video https://www.dropbox.com/s/sf0dlp5rra57vde/BUG UNDESIGNATE.mp4?dl=0

Run as administrator... new release beta https://github.com/Santi871/DCSWaypointEditor/releases/tag/v1.0.0b1

OpenBeta last release on 05/27/2021. I have assigned 4 different TOOs to my Jdams. When I clicked on undesignate before launching them, it deleted all assigned TOOs.

You can see a short 30 sec. video with the bug here: https://www.dropbox.com/s/ksqdgsqgte3qjmc/PROVA.mp4?dl=0 The designation does not happen on the selected wp, but on the position where the TPOD sensor is even if there was no target designation. Also when the designation is removed, the TPOD sensor moves further close to the aircraft. Same thing if you try to designate the points marked with markpoint, the designation moves to the sensor position of the TPOD.

In DCS / Options / Controls / your favourite aircraft, on the botton left there is Modifier/Switch. You can add a Modifier on the left side, and set it to a joystick button (pinkie paddle on the joystick for me); so it acts as a "shift", when it is hold pressed, all other bottons do other commands than the normal without it. Instead if you want make more profiles, like one for A/A, one for A/G, one for NAV, you need add one or more switch on the right side. They acts as CapsLock, when it is activated, it changes all the assigned commands ar the buttons. I use CapsLock and BlockScorr because they have 2 states: pressed and not pressed. You can use other switch on the base of throttle of the warthog, the have 2 states. Sorry for my english... Inviato dal mio SM-A530F utilizzando Tapatalk

I write you a message Inviato dal mio SM-A530F utilizzando Tapatalk