Rocky49 Posted October 10, 2013 Share Posted October 10, 2013 Hamblue Are you saying that your throttle setting matches when you start the quick missions? I always need to move my throttle when joining a flight in the air because the throttle setting does not match where my throttle is set....i ususally move the throttle up towards max but the aircraft may be already at a reduced throttle setting so my guessament of where to place the throttle may be off so I move my throttle to sinc it with the current actual setting...make sense to you? System:Motherboard Asus ROG Strix Z390-E,Asus ROG GeForce RTX 2080Ti OC, GPU, 32GB Corsair Vengeance DDR4 Ram, Intel i9 9900K @ 5 GHz , cooled by NZXT Kraken X52, Acer XB270HU G-Sinc monitor, Windows 10 Pro, Warthog joystick and throttle with wasy extension, VBK Gunfighter Pro and MCG Pro,MFG Rudder, running on a dedicated 1TB Samsung 970 Pro M2 Nvme , Super Wheel Stand Pro, with a HP Reverb G2 Link to comment Share on other sites More sharing options...
kk0425 Posted October 10, 2013 Share Posted October 10, 2013 Even though OP's question was answered I'm getting a slightly similar bug that some others in this thread are getting. I sometimes have to push the throttles past the cut off detent several times to get the engines started and here's the strange part, this bug only happens when I have my home built electrical panel plugged in too. But it seems to only affect the throttles. Everything else works correctly, aside from maybe making the game less stable too, but that's something I can't confirm at this time. Link to comment Share on other sites More sharing options...
Hamblue Posted October 10, 2013 Share Posted October 10, 2013 (edited) Glad the op got things working. Sorry to piss him off but sometimes you have to bark to get past the tunnel vision we all get. For those still with the problem. When we say to lift the throttles we mean grab it and pull them up towards the ceiling until it stops. While holding them UP towards the ceiling pull back. They will travel quite a bit more. The light bulb will go off in your head when you first get it. It took me several months. Also they wont sync until they're back. If joining in air you'll have to experiment. I personally always cold start. The reason they don't move until set correctly is that the right throttle has to be in the Off position for the left engine to start. It has to do with APU bleed air. Good Luck <S> Edited October 10, 2013 by Hamblue Asus Sabertooth P67 Motherboard 2600k CPU, 16 gig DDR3, 1600. Samsung 830, 256 gig hard drive, GTX780 Video Card, Warthog Hotas, Razer Mamba mouse. Saitek Combat Rudder Pedals. Trackir 5, Verizon FIOS 25Meg Up/Down Link to comment Share on other sites More sharing options...
AhSoul Posted October 10, 2013 Share Posted October 10, 2013 My throttles are definitely all the way up and back when loading into the cold start. [sIGPIC][/sIGPIC] Soul's pit thread Link to comment Share on other sites More sharing options...
Milli Posted October 11, 2013 Share Posted October 11, 2013 My throttles are definitely all the way up and back when loading into the cold start. Yep, same here. Its not us doing anything wrong. Regards, Millii Link to comment Share on other sites More sharing options...
jay43 Posted October 11, 2013 Share Posted October 11, 2013 Check calibration in joy.cpl, if you haven't calibrated it do so. Also if you have a stick extension re-calibrating the base will result in a more stable axis and allow full use of the axis in DCS without the need for any saturation or curve to reduce the throw. Eagles may soar high but weasel's don't get sucked into jet engines. System Spec. Monitors: Samsung 570DX & Rift CV1 Mobo: MSI Godlike gaming X-99A CPU: Intel i7 5930K @ 3.50Ghz RAM: 32gb GPU: EVGA Nvidia GTX 980Ti VR Ready Cooling: Predator 360 Power Supply: OCZ ZX Series 80 Plus Gold Drives: Samsung SSD's 1tb, 500g plus others with OS Win10 64 bit Link to comment Share on other sites More sharing options...
Dhorse Posted December 19, 2015 Share Posted December 19, 2015 Any updates in this matter? I have the same issue when using the T.A.R.G.E.T and mapped controlls for/ in the F15. Tried both in game "synchronize " option on and off. Most of the time the other buttons works but throttle either shuts down engines or does not respond at all :/ Link to comment Share on other sites More sharing options...
Dhorse Posted December 19, 2015 Share Posted December 19, 2015 Seems like the throttle Axis control is "Slider1" in 1.5 and not "DX_Throttle_Axis"(Thrustmasters T.A.R.G.E.T software) = "JOY_Z"(in game controlls). Anyway there seems to be no way of controlling the F-15 engines as left and right with the Thrustmasters HOTAS Warthogs throttle left and right. Hopefully just a bug that will be solved soon :) Will try in 1.2 and 2.0 now as well :) Now I´m running the "Synchronize" ON can be added, not sure if that matters for the F-15 and T.A.R.G.E.T Link to comment Share on other sites More sharing options...
Aeger Posted December 21, 2015 Share Posted December 21, 2015 (edited) Even though OP's question was answered I'm getting a slightly similar bug that some others in this thread are getting. I sometimes have to push the throttles past the cut off detent several times to get the engines started and here's the strange part, this bug only happens when I have my home built electrical panel plugged in too. But it seems to only affect the throttles. Everything else works correctly, aside from maybe making the game less stable too, but that's something I can't confirm at this time. Hi kk0425, I described this problem in thread http://forums.eagle.ru/showthread.php?t=155338. Edit: I'll try to get a video posted of the issue... Edited December 21, 2015 by Aeger [sIGPIC][/sIGPIC] Link to comment Share on other sites More sharing options...
Aeger Posted December 22, 2015 Share Posted December 22, 2015 After spending some time with this issue I found if I try playing the game with my TM flight stick disconnected, I can start engines fine. For the sake of pinpointing the problem, can you guys try it as well? Just curious if it's only me or if this indicates some kind of general hardware conflict happening in game. [sIGPIC][/sIGPIC] Link to comment Share on other sites More sharing options...
Spathiphyllum Posted September 2, 2018 Share Posted September 2, 2018 Exact same issue, 2018... Link to comment Share on other sites More sharing options...
Recommended Posts