Jump to content

Where is the switch for "scan/track-while-scan" modes???


aap_flanker

Recommended Posts

hi everybody!

I'm looking for some help...

I'm finishing the design process of su-27 switch panel, but in the draws that I found I just can't be abble to found the toggle switch that is employed to select between "scan" (OBZ) and "track-while-scan"(SNP) modes.

 

any ideas????

 

 

thanks

Intel i5 11700F + H80 | 4x4GB 3200mhz RAM | AORUS ELITE B560M | Samsung 850 PRO SSD 256gb| KINGSTON SA400 480GB SSD | WD 500GB | Gigabyte GTX 1070 8GB | Antec 1200 PSU | Thrustmaster Warthog HOTAS and homemade panels and rudder pedals | 24" Samsung T24C550 @60Hz 2ms | Opentrack 3 led clip

Link to comment
Share on other sites

I think when you switch from зах руч (manual target lock) to зах авт (auto target lock) it also initiates mode switch from SCAN to TWS. It lasts until you move radar cursor near target when it should lock it and change to STT

I looked at schema and couldn't find it either. So, this is only idea...


Edited by JLZ

[sIGPIC][/sIGPIC]

Link to comment
Share on other sites

I think when you switch from зах руч (manual target lock) to зах авт (auto target lock) it also initiates mode switch from SCAN to TWS. It lasts until you move radar cursor near target when it should lock it and change to STT

I looked at schema and couldn't find it either. So, this is only idea...

 

 

I read that this switch is for "auto lock closest target" or manual...

I'm thinking that may be this is the switch....

 

The track-while-scan mode should keep tracking targets after the lock of a target... it's correct????

 

:helpsmilie:

Intel i5 11700F + H80 | 4x4GB 3200mhz RAM | AORUS ELITE B560M | Samsung 850 PRO SSD 256gb| KINGSTON SA400 480GB SSD | WD 500GB | Gigabyte GTX 1070 8GB | Antec 1200 PSU | Thrustmaster Warthog HOTAS and homemade panels and rudder pedals | 24" Samsung T24C550 @60Hz 2ms | Opentrack 3 led clip

Link to comment
Share on other sites

As far as I observed in game...

While in TWS you move radar cursor on target. Then cursor moves together with that target (and radar keep searching for other targets too) until target gets in 85% of selected weapon. Then it switches to STT and you loose others.

[sIGPIC][/sIGPIC]

Link to comment
Share on other sites

I think this will be the mistery of the century hehe:music_whistling:

 

now I've been thinking in the MFD (or HDD) and I was asking the purpose of the switches and knobs numerated in the picture...

Hope someone can help me :cry:

su27-cp3.JPG.f50313adfb64a5352cf0a27554c277bf.JPG

Intel i5 11700F + H80 | 4x4GB 3200mhz RAM | AORUS ELITE B560M | Samsung 850 PRO SSD 256gb| KINGSTON SA400 480GB SSD | WD 500GB | Gigabyte GTX 1070 8GB | Antec 1200 PSU | Thrustmaster Warthog HOTAS and homemade panels and rudder pedals | 24" Samsung T24C550 @60Hz 2ms | Opentrack 3 led clip

Link to comment
Share on other sites

#3 in the photo is just a knob to adjust brightness.

 

Thanks

:doh: it's so simply XD

Intel i5 11700F + H80 | 4x4GB 3200mhz RAM | AORUS ELITE B560M | Samsung 850 PRO SSD 256gb| KINGSTON SA400 480GB SSD | WD 500GB | Gigabyte GTX 1070 8GB | Antec 1200 PSU | Thrustmaster Warthog HOTAS and homemade panels and rudder pedals | 24" Samsung T24C550 @60Hz 2ms | Opentrack 3 led clip

Link to comment
Share on other sites

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...